Would you build a 6.5 CM if you already had a x47L

[pyplynr]

I have a 6.5x 47 now and another being built at the moment. I'll be receiving my Stiller Tac30A/W with .308 bolt face in the next day or so. I also have a Manners T4 for it. I'm having trouble figuring out what caliber to make it. I have a Krieger 6.5 8tw barrel and a Rock Creek 30 cal 11.25tw barrel in my shop. Would I be wasting money on dies and brass if I had a 6.5 Creedmoor built since they are pretty much the same. What would you build on this action and stock? I've thought about making it a .308 with the barrel I have, but I hardly shoot my .308 that I have now since I got the x47 barrel for my Savage. Maybe something in 7mm? This rifle will be used for steel on my personal range that goes out to 1000 yards.

Thanks for your input.

 

[Layton]

Re: Would you build a 6.5 CM if you already had a x47L

How about a 6.5x55?

 

[excess]

Re: Would you build a 6.5 CM if you already had a x47L

The Creedmoor is nice if you want to buy off the shelf ammo, otherwise it's a near twin to your Lapua. A 7 might be a step up, but most that I can think of ( WSM, SAUM ) use a different bolt face. You could do a 7-08 I suppose.

 

[Goin'Hot]

Re: Would you build a 6.5 CM if you already had a x47L

At one time I had a 6.5x47, 6.5 Creed and a stupid 260 at the same time. It was a PITA having to load for all 3. If I were to do it all over again, I would have just stuck with one caliber and the 6.5x47 is a fine one.

 

[Bruiser_Joe]

Re: Would you build a 6.5 CM if you already had a x47L

they are all the same damn thing, get one and stick with it, if you want to expand on calibers, get a 7mm-08 or a mag like a 300wsm, 7wsm, 7saum, 6.5x284, 284rem, or get a 243, 6CM... pretty hard to go wrong with any of those.

 

[Layton]

Re: Would you build a 6.5 CM if you already had a x47L

Isn't the idea is to use one of the existing barrels so either a 6.5 or .308 cal.?? Did I miss sumin?

edt.. NV I did miss sumin.

 

[turbo54]

Re: Would you build a 6.5 CM if you already had a x47L

To directly answer the question: Yes, it's a waste UNLESS the intent is to use the x47 for matches where you recover brass, and the CM for lost-brass matches. Still, the cost of a whole nother rifle buys a LOT of brass!

If it were me, I'd horse trade the 6.5 barrel for a 7mm, and build a 7-08, 7mm Creedmoor or 284. But I'm a 7mm guy...

 

[Bruiser_Joe]

Re: Would you build a 6.5 CM if you already had a x47L

if you stick with that bolt face- 7-08, 6CM, or 243 are my votes

 

[yellowjacket]

Re: Would you build a 6.5 CM if you already had a x47L

Make it a 6CM or 243

 

[fw707]

Re: Would you build a 6.5 CM if you already had a x47L

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Goin'Hot</div><div class="ubbcode-body">At one time I had a 6.5x47, 6.5 Creed and a stupid 260 at the same time. It was a PITA having to load for all 3. If I were to do it all over again, I would have just stuck with one caliber and the 6.5x47 is a fine one. </div></div>

That's some good advice right there.
I've got a 6.5x47 and a "stupid 260". Both are nice rifles, but I'm starting to wonder why I've got 2 calibers that are so close.

 

[leadbullet]

Re: Would you build a 6.5 CM if you already had a x47L

go with the .260, you can buy all kind of brass brands and/or neck up 243 cases for cheaper brass you won't worry about loosing.
cheers.

 

[hewlett260]

Re: Would you build a 6.5 CM if you already had a x47L

+1 to a 260, now that Lapua makes brass for the 260 it's the better choice if you reload, but for off the shelf ammo, the CM isn't bad either.

 

[Wylie Custom]

Re: Would you build a 6.5 CM if you already had a x47L

I just did a 260 on the Tac A/W and it is crazy accurate. The A/W action allows you to seat the 260 longer if you use a longer freebore reamer.

Also, I just spilt a 1000 pieces of brass at Midway and after the discount code it came out to like 42$ for a 100.

 

[STR]

Re: Would you build a 6.5 CM if you already had a x47L

Like BigJoe said, I would get a 6mm barrel and go 243. They scream all the way to 1000 yards. I also had the 47 Lapua, 6.5 CM, and the 260 Rem. Just sold the 47, which I turned into a 6.5 CM for the guy who bought it. All three 6.5s are great, but why build so many similar to one another rifles? The more calibers you have, the more reloading stuff you will need. Just a thought

 

[pyplynr]

Re: Would you build a 6.5 CM if you already had a x47L

I'm already set up for the 6.5x47 lapua with over 500 pieces of brass. Going with 260 would be the same as 6.5 Creedmoor. If I were to go with either the 6.5 Creed or 260 it would be the Creedmoor. But, I'd like something different then what I have already or like someone else said, just stick with another x47. I might just go with a short barreled x47 Lapua 20"ish. I also already have a .284 Win on a long action so I don't think the 7-08 would beat that for just shooting steel. Maybe go ahead and do a 18" 308. 243 doesn't seem bad either. Hell I can't decide.

 

[Twisted300Win MAG]

Re: Would you build a 6.5 CM if you already had a x47L

6 mm remington or .243AI. There are plenty of people on here you could sell the barrels you have to cover the cost of a new one. Or keep them for spares for your existing rifles. Just a thought.

 

[pyplynr]

Re: Would you build a 6.5 CM if you already had a x47L

Ok, I'm leaning towards .243 win. What could I expect with the .243 with a short barrel(say 18") and bullet weights around 105-115? Is that too short?

 

[Cigarcop]

Re: Would you build a 6.5 CM if you already had a x47L

I love short barrels but at 18" for a .243 your killing that caliber. Just my 2ct.

 

[phreakmode]

Re: Would you build a 6.5 CM if you already had a x47L

I specifically chose 6.5x47L as I went with an 18" barrel length on the build, it has proven to be a performer.

 

[pyplynr]

Re: Would you build a 6.5 CM if you already had a x47L

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Cigarcop</div><div class="ubbcode-body">I love short barrels but at 18" for a .243 your killing that caliber. Just my 2ct.</div></div>

That's what I was afraid of.

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: phreakmode</div><div class="ubbcode-body">I specifically chose 6.5x47L as I went with an 18" barrel length on the build, it has proven to be a performer.</div></div>

This would make a good fit since I'm already set up for x47Lapua.
What bullet weight are you using? What kind of velocity are you getting?

 

[swampbuck]

Re: Would you build a 6.5 CM if you already had a x47L

I love rifles and I have a pretty respectable stable but I don't think you need another short action rifle. I would probably trade the action and stock for long action parts or a short action with a magnum bolt face. I would be looking at 280, 280AI, 300 Mag, or a Short mag. Or I would spend the money on glass, or misc. shit. If you got a 1000 yard range the old 4 wheeler might need a tune up.

 

[F224]

Re: Would you build a 6.5 CM if you already had a x47L

Are you building for the fun of building or for serious target work? Regardless of your reason, take a serious look at the 6mmBR Norma, soft shooter, lite report and cheap to run.

 

[phreakmode]

Re: Would you build a 6.5 CM if you already had a x47L

2925fps 123gr Scenar
2770fps 140gr Hybrid


<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: pyplynr</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Cigarcop</div><div class="ubbcode-body">I love short barrels but at 18" for a .243 your killing that caliber. Just my 2ct.</div></div>

That's what I was afraid of.

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: phreakmode</div><div class="ubbcode-body">I specifically chose 6.5x47L as I went with an 18" barrel length on the build, it has proven to be a performer.</div></div>

This would make a good fit since I'm already set up for x47Lapua.
What bullet weight are you using? What kind of velocity are you getting? </div></div>

 

[tylerw02]

Re: Would you build a 6.5 CM if you already had a x47L

I will soon be getting a Tac30 A/W. I currently own a 6.5x47L.

For those times I can't recover my brass and just to have cheaper brass in general, I'm going to build a .260 Rem for the reasons sledge said above...the increased OAL of A/W mags is a definite advantage.

If you were to only use AICS mags, the 6.5 Creed or 6.5x47L would be the way to go.

 

[JByrd]

Re: Would you build a 6.5 CM if you already had a x47L

Send your 6.5 kreiger barrel to your smith and have him chamber 2 bbl's for the other x47 he's building you sell your stock and action buy tons of powder and bullets and shoot the crap out of the two 47's you got. Tag team them as the barrels wear and go back to the shop.those 2 rifles will do everything you need to do and you will always have a fresh gun. Now go choot em!!!!!

 

[FequalsMA]

Re: Would you build a 6.5 CM if you already had a x47L

Go with a 6-X47 You alread have brass and will only need a seating die and some bushings.