Recent content by 25IA260

Re: .223 holes at 500yrds Thank you all for the replies an comments.. some interesting input i really like that artical on 6BR... Very helpful thanks i guess thinking $ its an impossable task at my level i'll keep dreaming for now ...

Howdy Folks i'm wondering what kind of spotter scope would be able to see .223 hole on white paper at 500yrds 700 /.223 .. weaver 36X... barely can see them at 400 when the light an heatwaves are kind to me... i was tossing the idea of a Orion ULX 66mm ED Zoom Spotting Scope. wondering whay...

Re: dies redding Chad thanks i already sent those dies back an yes a reorder of series B was made at the same time the #'s are 80317 an 81317 i'll be be going up to the club i have a application in to an roll it around there appreciate the offer an advice,... thanks Rich..

Re: dies redding i did some research an i understand what your saying did some visual look at parts for both types of dies S an B series lets say i have the proper bushing in hand... what end do you put it in the die from... from the top where the decap shaft is or the bottom where the case...

Re: dies redding i'd really like to know the answer to the problem but i sent the dies back there is some sort of a mis match with the set.. i went an used the body die an it did move the shoulder... the inside of the body die looked exactly like the neck sizer i figure if there was a...

Re: dies redding don't have a way to accurately measure the neck thickness but i get with the dial calipers 15thousand if subtract the bullet dia .243 from the OD .271 an didved by 2 i get 14 thousands.. so it must be close.. ? Edit; using as they came... box said complete ? Edit: on the...

Re: dies redding using as they came... box said complete ? Edit: on the box- part # 8317

Re: dies redding Ok... the case is 1.551 in length, OD neck is .271, ID .2435-.244 this on a fire case.. there was no change after running thru the neck dies as mention before i couldn't tell the size of the bushing .. it or whatever was inside the die an didn't come out or move one way or...

Ok i got a question on the redding S dies ... set came as marked complete.. had a neck sizing die, a body die an a bullet seat... do the bushing come out or able to move inside the die...???? thing is i couldn't get the neck tight enough to hold a bullet in place with or without the decapping...

Howdy i'm about to receive a 700 rem short in 6m Br has a heavy 20" ss barrel w 1~14 tw.. i wonder if i could get some of pet loading data from you 6m Br shooters ... i have on order lupau brass an have rem. sm. 7 1/2br primers on hand.. one of most conserns would be what is the heavist...

Re: Seating Die Test i'm kinda new an the info is over my head somewhat but shouldn't the test have been done first by annealing the brass i didn't notice whether or not he did .. maybe i mist something but after 4 firings i'd the brass has been worked a bit ? i did ejoy the artical an...

Re: Squib load after all these years i find myself back working on a rcbs single stage press an my T mag.. i started with a spar T an moved on to orangeT mag an then finally a 550B dillion one day i had a louder then normal BANG.. opening the bolt was normal but the case had no primer in...

Re: Winchester 748 powder good to know.. i just loaded some 125gr bullets in the .308 an i'm about to try the 748 powder has anyone used it with light bullets..?

Re: Clumped Powder...Safe? the part always bothers me i "PROBABLY".... near mis an almost pregnant

Re: Angle Shooting Question Nu B,...i don't know a thing about complicated formulas an how to figure the solution of changing poi i'm starting to shoot paper an learning but reading for interest on the question, it got me thinking .. if you took the bolt out of the gun an looked down thru...