• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by c3guns

  1. c3guns

    Rifle Scopes Athlon Ares ETR Gen2 vs DNT The One

    I just bought my second DNT "THEONE" and I think they are really good scopes. I know everyone adds "for the money" to the end of that statement for most all of these chinesium optics, but the truth is, they are very good by most measures, in many aspects. I do notice the vignetting at the...
  2. c3guns

    Leupold Mark4HD sighting in issues--- maxed travel

    I was fighting this same issue, except I could not get my MK4HD to aim low enough to get on target (was two feet high with the turret maxed out to the bottom). I swapped mounts and remounted the scope and, wa-la, perfect zero. I can't say for sure, but I'm pretty sure it was the recoil lug on...
  3. c3guns

    Can't get scope to zero low enough with 20MOA rail

    Correct, my mistake. it's the 183623. Fat fingered the keyboard or just retarded... Anywho, the zero stop is not causing the problem, best I can tell, as I've bottomed out the reticle with the turret cap completely removed, so no zero stop function in place, and the reticle is still too high to...
  4. c3guns

    Can't get scope to zero low enough with 20MOA rail

    You're right... Mine's the 183623...
  5. c3guns

    Can't get scope to zero low enough with 20MOA rail

    So looking at the scope's specs on the Leupold website, it states this model has 1 MOA clicks, with 40 MOA adjustment in each direction, which I take to mean with the reticle centered, it should have 40 clicks in up, down, left and right travel. The elevation turret maxes out with an indicated...
  6. c3guns

    Can't get scope to zero low enough with 20MOA rail

    This is very helpful. Makes me wonder if I need to remove the turret cap and rotate it past the "stop" and maybe it will give me more downward travel? Going to try this next, thanks!
  7. c3guns

    Can't get scope to zero low enough with 20MOA rail

    From the absolute bottom of the adjustment range, I have three full revolutions of adjustment.
  8. c3guns

    Can't get scope to zero low enough with 20MOA rail

    Not trying to zero at 25, just used that as a starting point to get on paper with a brand new rifle that's never been fired. It's not the zero stop, unless the scope is not functioning properly... I have the zero stop set to make the "zero" at the very bottom of the elevation adjustment range...
  9. c3guns

    Can't get scope to zero low enough with 20MOA rail

    My setup: Defiant Deviant action with 20MOA pic rail built-in 26" Bartlein 5R barrel 300Win Mag Leupold MK4HD 4.5-18x52 MOA #183624 Reptilia one-piece mount, 0 cant 190gr Hornady Match ammo (and others) My problem: Trying to zero this rifle at 25yds, hitting 5" above aim with the elevation...
  10. c3guns

    Anschutz AT-X folder in Pelican 1700?

    That insert is for a 54" case, and it appears to be designed to carry the rifle with the stock extended, not folded. My goal is to be able to run the shorter 1700 case since my rifle is only 30" long tip to butt with the stock folded.
  11. c3guns

    Anschutz AT-X folder in Pelican 1700?

    I have an Anschutz 54.18 in the AI-X Chassis with a folder, which I would like to carry in a Pelican 1700 with the stock folded, to make it as small a package as possible to transport. I plan to have custom foam cut to hold the rifle in the case. My concern is how wide the rifle is with the...
  12. c3guns

    Official Accuracy International AT-X

    Sorry, it's the American Rifle Company M Brace mount 20MOA, 1.5" height. All I'm trying to determine is if the AT-X forearm bridge piece will fit under my scope objective as I have it set up. I don't need a top pic rail for anything, and I only want the bridge add-on for the aesthetics of...
  13. c3guns

    Official Accuracy International AT-X

    Can anyone measure their AT-X and tell me the height of the forearm bridge from the top of the chassis forearm? Not to the top of the add-on picatinny rail, but the actual bridge itself. I am trying to determine if I have clearance to run the bridge on my Anschutz AT-X chassis with the scope...
  14. c3guns

    Murphy Precision scope mount for Anschutz 54.18MS question

    Trying to verify if the Murphy Precision picatinny rail adapter will work on an early 1980's Anschutz 54.18MS. This is the original silhouette rifle, NOT a repeater, and has a drilled/tapped receiver currently wearing Weaver #91 bases on top of the 11 degree dovetail. I would much rather go...
  15. c3guns

    Aftermarket cover for Leupold 12-40?

    Received my multicam cover and I am very happy with the construction, fit and finish, thank you very much. I, too would like to have the extended nose piece to cover the ARD when available, so please advise on how to "get in line for one of those".
See more
Top Bottom
Back
Home
Forums
Merch
Alerts