• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by Commander Shepard

  1. Commander Shepard

    Night Vision WTS Envision MARSc 1550nm Ballistic LRF (IR laser, IR illuminator, vis laser)

    48hr bump.
  2. Commander Shepard

    Night Vision WTS Envision MARSc 1550nm Ballistic LRF (IR laser, IR illuminator, vis laser)

    Bump.
  3. Commander Shepard

    Night Vision WTS Envision MARSc 1550nm Ballistic LRF (IR laser, IR illuminator, vis laser)

    I am selling my Envision MARSc 1550nm LRF, with built-in IR laser, IR illuminator, and visible laser. This is the commercial model, meaning the IR laser, illuminator and vis laser are not full-power. It does however have the 1550nm laser range finder of the FP MARS. I am the first owner and I...
  4. Commander Shepard

    SP10M vs SP10

    They are stacked, one after the other.
  5. Commander Shepard

    SP10M vs SP10

    My bad, I stand corrected.
  6. Commander Shepard

    SP10M vs SP10

    SP10M: - Heavier Bartlein barrel, bonded to upper. - Lever adjustable gas block, longer gas system. - Dual, longer buffer spring. I think that's about it.
  7. Commander Shepard

    Rifle Scopes ED Glass and Super ED Glass

    Works only if you lap the rings first.
  8. Commander Shepard

    Accuracy International AT-X

    You are absolutely right, I checked my order and it was in fact AI-29394BL. I didn’t know there was a second option available, is this a new offering? This brings up another question, why are there two different options for the same rail? Who would want one without the recoil lugs and correct...
  9. Commander Shepard

    Accuracy International AT-X

    Not in my experience. My AT-X high action rail came with no recoil lugs and the attachment screws were way too long. My recommendation is to still go with the AT-X high action rail, swap the recoil lugs over, and use the corresponding AT-X 20MOA NV rail. Doing anything else just increases the...
  10. Commander Shepard

    Accuracy International AT-X

    I^2 clip-ons are generally more forgiving than thermals alignment-wise. You should be good with the extra 20MOA. If you end up using a thermal, it may or may not cause an issue, I've seen it go both ways. I went with 0MOA 1.5", AT-X high rail, and full length bridge. Alignment is perfect.
  11. Commander Shepard

    Accuracy International AT-X

    Torque specs are 35 in-lbs and blue loctite. Not sure on the actual screw specs, I don't want to give you the wrong info.
  12. Commander Shepard

    Bulletseeker Mach 4 doppler chrono

    I am pretty excited about this one. It fixes every single complaint I’ve ever had with Magnetospeed and Labradar, if it performs as advertised.
  13. Commander Shepard

    Night Vision EOTECH CLIP ON THERMALS ( Full details)

    That is awesome to hear. I take back what I said about the design!
  14. Commander Shepard

    Night Vision EOTECH CLIP ON THERMALS ( Full details)

    I don't have much experience with the INOD and I've never seen the xELR, however I do have a few years' worth of time using a HISS-XLR. I don't recall it pixelating as much even when zoomed in to 15-18x. That being said, I'm going from memory here and it's hard to compare that to a few pictures...
  15. Commander Shepard

    Night Vision EOTECH CLIP ON THERMALS ( Full details)

    Personal opinion here and I could be very wrong, but I think this one was driven by silly contract requirements. US cooled units generally don't have standalone modes and are optimized for clip-on performance. Also keep in mind foreign SOF units (even Brits and Canadians) have far lower budgets...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts