Recent content by Crash01

Re: Federal 210M LR primers, $60 per 1000 <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ReaperDriver</div><div class="ubbcode-body">$60???? That's absolutely highway robbery. I just got 5k in from grafs last week for $160/5000. That's $32 per 1000. I hope...

Re: Federal 215M IN STOCK at Midway Damn that was fast. The 215Ms are gone, but... Regular 215s are still in stock: http://www.midwayusa.com/viewProduct/?productNumber=814002

Federal 215M AND 215 primers are in stock at Midway. Link: http://www.midwayusa.com/viewproduct/?productnumber=385649 Just and FYI for those that are looking.

Re: Hey Guys I need some help with Redding dies.... Give me a few minutes, I don't have a scanner so I'll have to take pictures and then get them loaded up. BRB. The pics are big so I'm not going to embed them. Here are the links...

Re: Redding Competition Neck Sizing Die Bushing Ma Sorry for the delay in updating the situation. I was able to try a .365 bushing and it did not have the issue that the .366 die did. I received the following reply from Redding: <div class="ubbcode-block"><div...

Re: Redding Competition Neck Sizing Die Bushing Marks? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: MitchAlsup</div><div class="ubbcode-body">I see no chamfer on the outside of the neck. </div></div> The angle of the photo is a bit misleading. All brass was...

Re: Redding Competition Neck Sizing Die Bushing Marks? Thanks for the info ReaperDriver. I used case lube as well. I also tried one without lube, and it did the exact same thing. As for Lapua brass being ready to go right out of the box, about 1/4 of mine had the necks pushed in so far that I...

Re: Redding Competition Neck Sizing Die Bushing Marks? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: JpS</div><div class="ubbcode-body">DO NOT FIRE these cartridges before having a measurement (with caliper) of the neck. It sounds bad : little dents on the top...

I have a brand new Redding Competition Neck Sizing die with a Titanium Nitride .366 Bushing, and I'm reloading on brand new Lapua brass. After neck sizing, you can see these very slight gouges in the brass. Is this normal? And, will it have any effect on the neck sealing when firing? I'm new...

Re: FN SCAR One last point on the magazines. This is from page 18 of the manual: <div class="ubbcode-block"><div class="ubbcode-header">Quote:</div><div class="ubbcode-body"><span style="font-weight: bold">12. Magazine Capacity</span> The SCAR 16S magazine is unique for the rifle and should...

Re: FN SCAR Some Scar pics in case anyone is interested. I received funds from my sale today, and will be shipping out tomorrow. If there are any last minute pic requests, I'll try to address them tomorrow before I head down to Fedex.

Re: FN SCAR I just went and re-checked again. The problem is there is too much material in this location: After removing just a little bit of material, that freed up the bolt catch and I was able to cycle normally. Also, what was said about PMags not dropping free was very true. They were...

Re: FN SCAR <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Kahuna</div><div class="ubbcode-body">They'll accept almost anyone's mags, despite what the manual says, although some PMags don't drop free. They're going for around $3500 on GB and Sturm... K...

Just a heads up fellas, for you guys who were looking to pick one up. I ordered mine Friday. Midway LINK

Re: Press for 338 lapua Anyone using the Forster Coax for 338LM? Your thoughts?