• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Recent content by drewh

  1. D

    DeLane Development Group Rimfire Ventures

    Hi Mike, With regards to your new action designs, any thoughts of offering a Smaller barrel tenon. I know in the BR world a .750-16 is pretty common, so that barrels in the .850-.900 diameter range can be used. I myself have a 1.20 straight version , and sent it off for testing at Whidden...
  2. D

    DeLane Development Group Rimfire Ventures

    Thumb button, Please.
  3. D

    DeLane Development Group Rimfire Ventures

    Most of what I shoot has 10 round stages, so I would like those available. Would a 5 round be shorter, or use the same body. a 5 round would be nice to have.
  4. D

    DeLane Development Group Rimfire Ventures

    Mike, If we have more than one rifle/generation should we respond once for each generation we have?
  5. D

    DeLane Development Group Rimfire Ventures

    Parts-wise, are you planning on the left handed models as well. Not as big of a demand I know, but that's the reason I went to Vudoo in the first place, now I have 2 repeaters and a single shot..
  6. D

    DeLane Development Group Rimfire Ventures

    While I don't have a specific need at the moment, I do like the Vudoo bottom metal on my gen 1 Sinister and am thinking of moving my gen 2 into a stock vs chassis. Will you be offering action wrenches, kick myself for not getting those when available.
  7. D

    Unavailable Lefty Vudoo 360 - What to do now

    Confirmed. I asked about parts because I have a couple Yes, we are discontinuing LH for now. We are considering doing some limited runs of LH actions in the future. We will still have parts to service LH guns Chris Dzwonek | Customer Service Offi
  8. D

    Who to rebarrel Gen 1 Vudoo?

    S&S Precision in Denton has done quite a few locally including 1 of mine and 1 in the works. I have been very happy with the work.
  9. D

    50gr Curx what powders have you used?

    Original plan was to use a match reamer with no rim cutter, run in deep enough for the 50gr bullet, but currently looking at using a known good match reamer and extending the chamber with a throater, since the reamer is not done yet.
  10. D

    50gr Curx what powders have you used?

    They sent me the 50gr sheet - only has 3 powders with loads, list a bunch of others, but no data. I have titegroup, Enforcer and longshot to try after it gets put together. Thanks for the input.
  11. D

    50gr Curx what powders have you used?

    Ready to go down the 50gr CuRx path, but load data is pretty sparse. What powders have you used with success. If the powder is on the list with no min/max, how do you figure out a starting point?
  12. D

    Curx dies

    For those of you loading , or who have bought the die set, did yours come with a threaded seater so you can use it in a press or only the hand option? My set came with the hand seater, and I would prefer to have the press type. I have called Cutting Edge, but haven’t heard back.
  13. D

    Ramshot Enforcer with CuRx bullets

    I have never used alox, did you treat the whole bullet prior to loading?
  14. D

    Ramshot Enforcer with CuRx bullets

    What do you use for that, off the shelf or homemade?
  15. D

    Ramshot Enforcer with CuRx bullets

    Thank you for all of the input. I have several ideas about how I can make consistent ammo, we shall see. I will post some results when I get there, it will likely be a few weeks before I get all of the items I need, and can start.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts