• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by Enios

  1. Enios

    What bullets are your favorite for target .308 WIN

    Re: What bullets are your favorite for target .308 WIN 190 SMK's over 41.3 AA 2520 and doing 2510... 175 SMK's over 44.6 Varget doing 2710... Both in Nosler brass with the 210M primer... Savage 10 FCP HS tactical in 1/10 twist.... When using Winchester brass I have to up charge .4 grain...
  2. Enios

    bullet weight w/ a 1/9 twist

    Re: bullet weight w/ a 1/9 twist They also teach us respect .... Man asked a simple question ... If you have the ability to change the barrel yourself I would change the barrel ... cutting 8" off the barrel will cost you 200 fps or more in velocity which will shorten your distance where you...
  3. Enios

    RCBS 5-0-5 Trouble Zeroing. (Pics)

    Re: RCBS 5-0-5 Trouble Zeroing. (Pics) <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Fuzzball</div><div class="ubbcode-body">The lead weights under the pan hanger cover are to level the beam and it appears CK's beam is fine. The screw foot is used to level the...
  4. Enios

    RCBS 5-0-5 Trouble Zeroing. (Pics)

    Re: RCBS 5-0-5 Trouble Zeroing. (Pics) I've never used the 5-0-5 but my 10-10's have weights under the pan and you can take the screw out and remove some of the weight to zero....
  5. Enios

    Cases beginning to get too short. What to do next?

    Re: Cases beginning to get too short. What to do next? Never bought a piece of Nosler brass yet that wasn't well below trim length and problem could be 2 fold if you are excessively sizing them.... Usually have to be shot 3 or 4 times and sometimes more before they need to be trimmed... Got...
  6. Enios

    chrony questions

    Re: chrony questions When light out isn't good you are not suppose to use your screens... found this out one day by reading instructions... known load was running about 200fps to slow and I couldn't figure out what was going on... read instructions and it said not to use screens on a cloudy...
  7. Enios

    chrony questions

    Re: chrony questions I own both and have had to replace the Chrony, because it didn't do well with the little brother 7 RUM at 10 ft repeatedly... It was replaced at no charge and no problems in the last 2 years... We did get the CED when I sent it back and love the unit, but for the...
  8. Enios

    Neck Tension Question

    Re: Neck Tension Question Quite by accident last night I had been trying out my new SS media.. I had 50 rds ready to go and had checked with a bullet (tried to push it in by hand) to see if I had necked sized already.. Well had them primed and loaded and when I started to seat bullets it...
  9. Enios

    Stainless Steel Media Testimonials

    Re: Stainless Steel Media Testimonials Well I'm pleased with my set up and after a quick look around found a pretty quick and easy way to dry my brass... something like this may already be here, but I've looked at over half this post and hadn't seen anything like this... If there is excuse my...
  10. Enios

    Ackley fireforming question

    Re: Ackley fireforming question Way I used my go gauge, should be around.03... If I did it right... I know I got the feel just as describe it should be when I bolt fresh brass.. I snugged barrel to the go gauge and tighten nut and the line up marks I put on it barely move apart...
  11. Enios

    chrony questions

    Re: chrony questions If you look at the two below it I have both and like them both.. the CED has a lot more bells and whistles but have lined them up back to front more than once and only get a few fps difference in the readings... Like using the chrony when setting up at target... Not...
  12. Enios

    Annealing Machines

    Re: Annealing Machines Looking and researching for a couple of years now... seen one in action and know at some point I will put the Hornady kit away and replace it with the Bench Source... look on You Tube and you can find most of them in action...
  13. Enios

    Ackley fireforming question

    Re: Ackley fireforming question When I put my 243 AI together I used some know loads that were near max with 95 SMK's... Got a one hole 5 shot group and many 1/2" group while playing... Set my barrel up to just slightly crush a factory round when I put here together and makes a pretty little...
  14. Enios

    Data for ALL Cals Ackley Imp

    Re: Data for ALL Cals Ackley Imp 26" Shilen 1/8 243 AI, 105 Berger VLD Match Hunting, 41.5 RL-17 3065 fps... all 5 shot groups under 1/2 with most in 1/4" or smaller. Seating bullet .010 of the lands in fire formed Lapua Brass neck sized to hold .001 tension with Fed 210M primers.
  15. Enios

    Need help with .308 reloading

    Re: Need help with .308 reloading Unless you have an unusually thick neck you would be better off with the .336. .015 neck thickness with a 308 bullet figures out to .338 which will leave you no neck tension....
See more
Top Bottom
Back
Home
Forums
Merch
Alerts