• Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    Drop it in the replies for the chance to win a free shirt!

    Join the contest

Recent content by ericf

  1. E

    Shooting benches

    Made up three of these today. All 2x6's and telephone pole. Stable beyond belief. The stools arent shown.
    • Thread
  2. E

    Shooting benches

    in reality they turned out nicer then I anticipated. We were concerned about wind on the hill top, but they are so heavy, it will have to be a tornado. The table on the plateau is facing directly where we are planning a 1K yd target gong on the hillside. Sort of in the valley area. Just to...
  3. E

    Shooting benches

    Blanco Texas
  4. E

    Shooting benches

    Made up three of these today. All 2x6's and telephone pole. Stable beyond belief. The stools arent shown.
  5. E

    Tikka T3 Thread

    Does anyone have , or know where to find a schematic drawing or total disassembly on the TacA1 trigger? Im assuming its the same as the CTR and all other T3 triggers.
  6. E

    Remington 700P barreled action

    for those that know,,,, Does the HS precision stock on the Police 700 have any resale value? I have this stock now and want to drop the rifle into a fully adjustable stock set. My HS police stock has CDI bottom metal (inlet done by CDI) and was professionally bedded to my action. All of...
  7. E

    Tikka T3 Thread

    In comparing my T3x Tac To my TRG22, I believe that if everything was equal in potential accuracy, The TRG trigger would be the game changer between the two. It's far superior to the TacA1.
  8. E

    Tikka T3 Thread

    Has anyone attemted to slightly open the the "lips" of the magazine port of the TRG stock to let the T3x magazine fully seat? It appears that only about .25" or so would need to be inletted/opened to allow the floor plate sides to clear. And further logic says the TRG mag fit wouldn't be...
  9. E

    Tikka T3 Thread

    Is there a replacement cheekpiece for the TAC A1 chassis available that has lateral adustments ? I'm Rt. handed and need a little Rt. shift on the cheek riser. I can't seem to find anything. I can't even locate a replacement riser, period.
  10. E

    gap 10 gas block

    My GAP 10 has the Noveske switchblock and it appears to have one set screw in the bottom
  11. E

    Resizing brass

    never mind, this was done years ago for a bench gun. Not a semi-auto. Age is a terrible thing
  12. E

    Best .308 for running suppressed?

    Re: Best .308 for running suppressed? I just picked up the SigSauer 716. I haven't had it out yet, but it seems to fit the criteria you listed and is about 50% less cost. Appears well thought out and is a typical representation of Sigs attention to detail. Piston driven, 4 position gas block...
  13. E

    Rifle Scopes Aimpoint CompML3 DO I have a problem??

    Re: Aimpoint CompML3 DO I have a problem?? I'm looking through the sight as though I was going to fire (actually aiming). I have no strange head tilt, nor weird viewing angle. I'm just looking Straight through the glass. Outdoor lighting shows single red line through lens. (see above...
  14. E

    Rifle Scopes Aimpoint CompML3 DO I have a problem??

    Re: Aimpoint CompML3 DO I have a problem?? I just went outside with it. If the scope is pointed at any darker background, (red brick wall, plants, trees, fence, etc.) I still get a red thread diagonal and visible across the view. Although Not nearly as bad (bright) as indoors. If...
  15. E

    Rifle Scopes Aimpoint CompML3 DO I have a problem??

    Re: Aimpoint CompML3 DO I have a problem?? I sent an email to Aimpoint attempting to explain the perceived problem. Hopefully they will respond. Maybe I should send them a photo also. One thing, It wasnt like this when purchased new. And it has only been to the range a few times. Never...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts