• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by greybeard

  1. G

    Off topic: Residential Water Heaters

    Just recently read about a CO2 water heater, split concept with the compressor outside and only the tank inside, water pipe between. Per reading, domestic hot water, at 175 degree requiring a tempering valve, + heating. Interesting reading.
  2. G

    MDT HS3 vs LSS-XL Gen2

    MDT josh, how is MDT involved with the ORYX stock? availiable now?
  3. G

    Gunsmithing chamber tooling Question

    https://cogsdill.com/products/burnishing-tools/gun-chamber-burnishing-tools/ Thought this was a interesting tool. Does any of the major barrel makers use this? Same Co Makes tool to deburr the inside of the gas port hole. https://cogsdill.com/products/deburring-tools/
  4. G

    Savage 111 build?

    I have a 110 Savage factory .223 from the factory. Heavy barrel. careful if you are looking for a detachable mag stock, other than a long action caliber. Action and internal mag that is attached to action should fit aftermarket stocks.????
  5. G

    783 Build

    Looked at the PDC chassis, assume this takes AICS mags? what mod had to mde from the standard inlet, or which one did they start with?
  6. G

    783 Build

    Also am wondering about the differences between the 700 and the 783 action as far as stock inlet etc. in other words what modifications to the inlet for 700, to fit the 783? How hard was it to fit this action in the chassis?
  7. G

    Ruger American ( the new 700)?

    How close to the 700 footprint is the Rem 783 for this type of project? Thought is to use the 783 action in a chassis system. Down the road home barrel change with the barrel nut?
  8. G

    Base .308 Rifles

    the point is is there a match to the inlet of the 700 to the 783? how close is it to the same , I don't have access to the rifle to measure the diffrences? that is what I am askin what is the diffrence between teh 783 and the 700?
  9. G

    Base .308 Rifles

    looking at a short barrel Truck/ hunting rifle. so far the choices are Ruger American for a as is setup. Savage Hog Hunter, may want to change to a diffrent stock or a chassis system? Remington 783, switch barrel like a Savage?, What trigger fits?, what is the inlet like? is this the...
  10. G

    Interesting New Entry Level Rifle The Ruger American Predator

    Could you not just bed action recesses into the new stock???, possibly tape on the front of the "V" for clearance (like a normal recoil lug)? how close in diameter is the bottom of the action to regular round actions? Assume this is a single feed setup, how close to feeding from "other" (AI, AR...
  11. G

    Bolt Action Rifles: So behind the times, here is what I want...

    Is this not what is being tried in the Ruger American and the Rem 770? using three bolt lugs and the barrel extension pressed in a aluminum tube for the receiver / scope and trigger mount? ( haven't looked that close to these yet)
  12. G

    Rifle Scopes Quality one piece scope mount for the AR platform?

    Take a look at the Armalite. Have two haven't had a problem.
  13. G

    Powder for .308 Match Loads

    What is your load for the 2000MR, 168AMAX and the 178AMAX.
  14. G

    Hide thoughts about FL resizeing vs. bump shoulder?

    edit in original post, bump
  15. G

    Hide thoughts about FL resizeing vs. bump shoulder?

    Since I have a need to review my reloading practices, I compared the length of FL sized brass to fired brass, ( measured from the base to a datam line on the shoulder), there is a .015 diffrence. is this too much? Had always set up the sizeing die by instructions to bottom die out on the...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts