• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by NotoriousAPP

  1. N

    Gunsmithing .30-06 barrel advice (length/twist)

    @WBB300: here is a link to an article with the Serengeti print at the bottom of the article: The Rifleman's Journal: Cartridges: Accuracy Secrets of the .30-06 - Part 1
  2. N

    Gunsmithing .30-06 barrel advice (length/twist)

    Thanks. I'm looking forward to it. I'll post results once it's built. Thanks everyone for your input.
  3. N

    Gunsmithing .30-06 barrel advice (length/twist)

    It sounds like we agree, in regards to precisions the pre-fit may not be as good as a custom, there's a slight chance that it could be but probably not. That's what I imaged it would be. To be truthful, the price difference between custom and pre-fit is not negligible. If I use the smithing...
  4. N

    Gunsmithing .30-06 barrel advice (length/twist)

    As a follow up to previous posts I did contact four gunsmiths regarding the barrel chambering and fitting, one was local and I have good experience with them, two were local and highly recommended, one was out of state and also highly recommended from a couple different sources; I also listened...
  5. N

    Gunsmithing .30-06 barrel advice (length/twist)

    I'm going the pre-fit route this time around. My options were Shilen and Criterion. Criterion only offers the SAAMI reamer, Shilen offers the SAAMI and the Match (print above) reamer. Just weighing my options. If either had the Serengeti reamer then I would have gone that route. I am very...
  6. N

    Gunsmithing .30-06 barrel advice (length/twist)

    If I won't have access to the PTG Serengeti, what are your opinions on this match chambering compared to the SAAMI spec chambering: "][/URL]
  7. N

    Gunsmithing .30-06 barrel advice (length/twist)

    That's how your post came across. Was that because you thought I was swapping barrels on a Rem action? I feel like this is rhetoric but.....do you need a machinist or gun smith to swap a savage barrel?
  8. N

    Gunsmithing .30-06 barrel advice (length/twist)

    You are partially correct. I don't know what I'm doing because I haven't learned how to do it yet. This isn't a matter of pride. The barrel is a Savage pre-fit for a Savage long action. The main advantage of the Savage platform is the semi-switch barrel capability. You're telling me that...
  9. N

    Gunsmithing .30-06 barrel advice (length/twist)

    A Noreen BN-36...nice! I love my Garands but I have to admit the BN-36 is sick. Please add link back in this thread to your testing results. Thanks.
  10. N

    Gunsmithing .30-06 barrel advice (length/twist)

    I appreciate the offer. I will pass this time. If I find that I have some serious accuracy issues then I'll take a serious look at re-cutting the chamber with a Serengeti reamer. I wouldn't really say I'm trying to do this on the cheap. I'm going this route for two main reasons: 1) This is...
  11. N

    Gunsmithing .30-06 barrel advice (length/twist)

    Sounds like I'll need to do some characterization with bullet weight/powder/seating depth....which I planned on doing anyways. I guess the worse case scenario is that I max out at 180-185 grain bullets....maybe 190 grains with a compressed load if I really want to do that. That's ok. I think...
  12. N

    Gunsmithing .30-06 barrel advice (length/twist)

    Follow up: Criterion sent me the link to the reamer print they use for their 30-06 chambering (they follow the SAAMI spec). Here it is: http://www.saami.org/PubResources/CC_Drawings/Rifle/30-06%20Springfield.pdf For reference, here is a link to an article where at the bottom you can see the...
  13. N

    Gunsmithing .30-06 barrel advice (length/twist)

    I think you guys should each bring your 30-06 rig and settle this with a dualing tree at 1000 yds.
  14. N

    Gunsmithing .30-06 barrel advice (length/twist)

    Thanks for the feedback. I'll post the reamer print when I get it.
  15. N

    Gunsmithing .30-06 barrel advice (length/twist)

    Forgot to mention that I did not receive the reamer print in my inbox. Were you sending it as a snipershide PM or my personal email?
See more
Top Bottom
Back
Home
Forums
Merch
Alerts