Recent content by nthor

Re: Help with 338 Lap mag in a AWM (UK) <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CoryT</div><div class="ubbcode-body">With a 44" vertical target area, that's 1.2 mil of error you can't see. Even S&B's need calibration, I've got a couple that run .104 per...

Re: Help with 338 Lap mag in a AWM (UK) <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CoryT</div><div class="ubbcode-body">First, is the scope calibrated? Second, how accurate are the ranges? Third, did you get to see where the hits were on the targets? Last...

Re: Help with 338 Lap mag in a AWM (UK) I have tried to but it crashes every time

Hi I have a AI AWM 338 Lap Mag and have found a load that performs well so far. I have just come back from a local range yesterday I will enter all data below and have tried to work back my scope data to make a full chart but its not liking what I achieved yesterday and I cant get the suggest...

Re: Can I sell a TRG 22 stock to the US? thanks for the info, yep dropped it in the wrong section, sorry all, have not done much of this posting stuff, apologies

Hi, quick question, I have bought a folding stock for my TRG 22 so am thinking of selling my black standard TRG 22 stock on ebay. Having seen so many TRG owners in the US would that be something I can post there or am I asking for trouble, after all its only a stock?

Re: AI 338 AWM help with scope issue please Well all working now, getting 3004 FPS with Lapua 250s but well over max pressure in curent load data. After calling Sporting Services here in the UK they advised a higher charge as load data has been scaled down. So worked up to their suggestion...

Re: AI 338 AWM help with scope issue please OK All Fixed Anyway, I took the scope and mount off the gun and noticed a small dowel pin that acts as a recoil lug, this looked like it could have held the mount a little high so I drifted it in a little 9not sure if this was the cause) Put...

Re: AI 338 AWM help with scope issue please ok thanks to you all for the help, my plan is a bit of all the advice, I will try and borrow my mate scope as he has the same and see if that gets down, at least I will rule out the scope. Then if his scope has the same issue I will try his mount...

Re: AI 338 AWM help with scope issue please hi, thanks for the advice but have tried that as well, the rail is a 45moa I am about 27moa high with the scope bottomed out, I am told a lesser scope rail will not work with my scope due to size...but everyone tells me it should all be ok. I am...

Re: AI 338 AWM help with scope issue please someone suggested is the barrel bent, the rifle groups well, how would I confirm alignment?

Re: AI 338 AWM help with scope issue please something here is wrong, maybe me? I have just taken the turret off it was as low as you can get the scope as i tried some grips on the turret it is 100% at its bottom, i have about 260 clicks of elevation if i rotate clockwise. Scope is the double...

Re: AI 338 AWM help with scope issue please Hi I have checked the turret it will not go any lower, (have taken if off to make sure its free) Rail was with screws on left muzzle end of rail was lower than but end. Any ideas as everywhere quotes use a 45 MOA rail with this scope. thanks

Hi, I am in need of help as i am well stuck, I picked up a used AI 338 AWM with a S&B 5-25 x 56 PM2. My issue is with the scope wound down as far as I can get it i am still 54cm above point of aim at 100 yards and 94cm above point of aim at 200 yards, this would give a zero of about 600 yards...

Re: Unique Alpine hi not been here for a while but am back now, number on barrel was AAB0063, see what you can fine i am now on 347 rounds on 2nd barrel and its shooting 3" at 600yrds