Recent content by p e bragg

  1. P

    .22lr Colt M16 by Walther,Ulm

    You misspelled miss spell
  2. P

    Any interest in RWS 300WM Brass???

    I'd be in for 3-500 if it sells for $1.50
  3. P

    Another friend has cancer...

    Prayers sent. May God Bless him and his family. Muddy Waters 60
  4. P

    Gunsmithing Anyone Care....

    Could it be a deep hole drill or a doughnut conveyor belt??
  5. P

    Gunsmithing Nicks in brass

    Texastonk; I have exactly the same problem with my Win 70 in 22-250 that I bought new in 1974. This was before their short actions, just a LA with a blocked magazine. I think the problem is the timing of the ejection cycle . It starts to early and the cases get pulled up against the upper edge...
  6. P

    AA 3100

    Re: AA 3100 Jhedg; Have you tried IMR4831? I know that AA4350 shoots just like IMR4350 and I use the same IMR load data for the AA powder. I haven't used any AA3100 so I can't tell you if it is the same.
  7. P

    Propellant Profiles, 5th Edition

    Re: Propellant Profiles, 5th Edition Eastern ncnative; I bought that book late last year and read it all. It is mostly a reprint of all of the reviews that Handloader Magazine's authors wrote over the last 10 years. I found it interesting and gleaned some new info on a few of the powders...
  8. P

    Gunsmithing Rem 700 bolt lugs

    Re: Rem 700 bolt lugs I want to again thank everyone for their input on my problem. As to how far the bolt handle was raised, I don't really know. My grandson was too shocked at the time to remember. I am planning a rebuild for this rifle if my gunsmith checks everything out. I am just...
  9. P

    Gunsmithing Rem 700 bolt lugs

    Re: Rem 700 bolt lugs Gaslight; Ding,DING,DING!!!!! Guess what fell out of the bolt when I pulled on the shroud?? I found the blown primer cap. Thanks guys for all your help. I am going to give that bolt and trigger a good clensing and lube job. Forgive an old fart not thinking...
  10. P

    Gunsmithing Rem 700 bolt lugs

    Re: Rem 700 bolt lugs Immorteq; The bolt slides all the way into the notch. The bolt handle just does not want to turn down. I have the barreled action out of the stock and it is still a no-go. Thanks for your help Immorteq and SDLAW.
  11. P

    Gunsmithing Rem 700 bolt lugs

    Re: Rem 700 bolt lugs Immortec; I measured both behind and in front of the lugs and got the same measurment 0.6955". I even measured both ways, with the lugs and 90degrees opposite. Same measure. The extractor is fine and I can push the ejector back and forth and feel the spring pressure...
  12. P

    Gunsmithing Rem 700 bolt lugs

    What I need to know is whether my lugs have been set back due to what I think was an out of battery discharge or if something is lodged or broken inside of the bolt. The reason I am concerned is that my bolt won't close. My grandson was unloading the gun one evening and he says that when he...
  13. P

    Gunsmithing The Bolt Flutin Vid.

    Re: The Bolt Flutin Vid. Count me in for 2 LA Rem 700 bolts. I would also like to add 2 of the Nesika bolt shrouds. I will be sending them in the AM. Looking forwad to the GB on truing the receivers. Awesome effort on your part. Thanks a bunch.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts