• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by Precisions

  1. P

    Black Friday Deal @ Dick's - REM 700 for $449

    Dicks will never get any of my buisness again.
  2. P

    Neck Sizing Problem

    BB, I'm not going to bother quoting whats already there. Go back and read it. I honestly feel like I'm arguing with a fifth grader. You personally make a choice to take your time and post on a thread with a question, that you have no answer for. Then say to stop wasting time... LOL! You cant...
  3. P

    Neck Sizing Problem

    Buzzboss, once again I'm puzzled on how to respond to your input. you are a confusing Fu*%#r to deal with. as we all know, gouges and scratches in the dies come from dirt... Yea I'm guilty of resizing cases that aren't perfectly clean but so what. apparently you are too. Maybe your's aren't...
  4. P

    Neck Sizing Problem

    I should have posted that I'm using RCBS dies. no bushing. for both FL and neck sizing. The reason I wanted to start using the neck sizing die, is because its new and my FL die gouges up my cases. Not fixable, just too many cases through that thing. Buzzboss, What you're saying is mercy is the...
  5. P

    Neck Sizing Problem

    Still having this issue with my neck sizing die. I have figured out that its the extractor that is being a pain to slip onto the brass. When I slide the bolt in it will stop short. If I pull it back out from there, the round will not come back out. If from that position of the bolt stopping on...
  6. P

    Neck Sizing Problem

    2.8 works when fl sizing, and i did try to seat it even deeper with the nick sizing. also no marks on the bullet itself. its hard to see any marks on the case because there used
  7. P

    Neck Sizing Problem

    After neck sizing my once fired 308 Lapua brass in my Remington 700, it will fit in my chamber perfectly, and the bolt will close no problem withought the bullet seated. After seating the bullet to 2.8 the bolt will not close! I'm stumped. If I use my fl resizing die, it works no problem. Any...
  8. P

    Hard to close bolt and eject

    Recently had a hard to close bolt problem, and extraction problem... Thought it was because of my die set, but now thinking it could be extractor problem. When loading ammunition into the chamber it feels like the bolt gets stopped short. If I jam it, it will go in. But then I have to slap the...
  9. P

    Mixing Once Fired Brass With X Amount Fired Brass

    Just curious how many guys keep track of how many times they fire there brass and keep them together, and who keeps them separate if some have more firings than others.
  10. P

    Tight Bolt Close bad for chamber?

    Were not on the same page. Instructions tell me to kiss the shelholder and thats it. No turns to let off like Ive seen in other dies. Although i will do this sometimes to fine tune for headspace that I want. In other words, I cant get it any smaller.
  11. P

    Tight Bolt Close bad for chamber?

    Yes did both dies to instructions, but 1/8 1/4 and 1/2 turns will only increase headspace length. I was thinking the problem of tight bolt close was from excessive headspace. I dunno. The rcbs dies are working fine, and im going to give Hornady a call and see what they say about warranty if the...
  12. P

    Tight Bolt Close bad for chamber?

    Dont have a headspace gauge or 40 s&w case to check headspace, but i did take a fired 9mm case that does fit over the neck and onto the shoulder a little higher than the datum line. the measurement from the rcbs die was 1.695, and the measurement from the Hornady die was 1.700. No smearing on...
  13. P

    Tight Bolt Close bad for chamber?

    Picked up a new Remington 700 AAC-SD and loaded some rounds up to do some testing with. Come to find out they are hard as hell to chamber so I figured new rifle, maybe some debris in the chamber etc.. wiped it out, and cycled 20-30 rounds through the chamber without firing and the bolt was still...
  14. P

    ChuckNorris needs help picking a .308!

    Re: ChuckNorris needs help! Chuck Norris doesn't need help... Help needs Chuck Norris
  15. P

    Rifle Scopes Think this could be my scope?

    Re: Think this could be my scope? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: EXTREMEPREJUDICE</div><div class="ubbcode-body">You really don't have a good baseline to begin with so all the outputs from your data are suspect. I doubt that is your correct...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts