• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by Rory S Sallee

  1. R

    Member Link Up Shooting south of Denver

    Cofox. Look to Byers deer trail area for long range sniper community. Lived there a few years back. In Idaho much more gun friendly. South towards pueblo has some shooters too. Plenty of us old military guys if you sniff around.
  2. R

    Member Link Up Idaho members

    1,000 west of rexberg. Unified sportsmans club. F/TR, Palma, tactical matches and much more.
  3. R

    what Squeeze bag filler thats light weight

    Looking at competitions and dont want to lug rice, corn or sand. Whats a good light weight fill that is rigid enough to stand up to recoil and remain solid.
  4. R

    Rifle groups under .5in then opens to 1.5 after 10

    Re: Rifle groups under .5in then opens to 1.5 after 10 I do all that and compete quite a bit outside work. Will go back through and check again. Had another shooter fire a sub half and when warmed up did the same thing to him as well. Tried the cleaning thing with same results. Govt...
  5. R

    Rifle groups under .5in then opens to 1.5 after 10

    Re: Rifle groups under .5in then opens to 1.5 after 10 Good float on barrel, bagged and prone, and the stock is the M40 clone from McMillan in 700 type action. I also shoot F/TR and dont load the gun, free recoil. Still perplexed on the SD being 39 on a string of 10, knocking out the...
  6. R

    Rifle groups under .5in then opens to 1.5 after 10

    Re: Rifle groups under .5in then opens to 1.5 after 10 Older McMillan 700 type action
  7. R

    Rifle groups under .5in then opens to 1.5 after 10

    Re: Rifle groups under .5in then opens to 1.5 after 10 I keep falling back on the bedding as well and will have to take a look. Some where along the line the rifle was re-barreled and probably should have been looked at then, if it wasnt. Thanks,
  8. R

    Rifle groups under .5in then opens to 1.5 after 10

    Re: Rifle groups under .5in then opens to 1.5 after 10 For the first response I compete for the agency I work for and I have to use the ammo they provide. Trust me I would much rather tinker on it and work my own loads. I dont think its the rounds as the other guns we have dont run into...
  9. R

    Rifle groups under .5in then opens to 1.5 after 10

    Dont know why but I can shoot two 5 round groups under .5min and after that it opens up to 1.5min. .308Factory Hornady match A-Max in a McMillan Heavy palma contour and doesnt seem to get too warm. Had a round I attempted to fire twice and not a very good primer strike, never did go off. Also...
  10. R

    Rifle Scopes Eyes get fatiged and blur after being on the scope

    When on my scope for a string of shots after a while the target dot will blur and split into a double image. Happens with all my scopes. I have taken out the paralax and set the cross hairs to my eyes. I do need a prescription for reading and have tried shooting with and without the glasses...
  11. R

    Range Report Suggestions for a hand held ballistics computer?

    Re: Suggestions for a hand held ballistics computer? compete longrange F/TR and a current sniper for a Gov agency. I have the Ipod touch with the KAC bullet flight 3.0 military version. Outstanding and assisted on by Bryan Litz. I will let the unit speak for its self. You can put multiple...
  12. R

    Twin Falls, Idaho, Jan 1. PICTURES ARE UP

    Re: Twin Falls, Idaho, Jan 1. The Chosen Frozen Shoot New to this site, but shoot long range FTR up here in Idaho falls and we would welcome any newcomers up here this spring at our matches. Would like to hear more on sniper shoots and any related shoots you have down in your area. I need...
  13. R

    Gunsmithing bedding/stock issues?

    Re: bedding/stock issues? I do quite a bit of home gun work and purchased a Rem 700 SPS I cleared out the forend and ran two small aluminum rods down each side and filled in with epoxy. Make sure you rough up the inner area to be bedded for the epoxy to stick to. Good luck.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts