Recent content by rowrd
-
R
Inguinal hernia laparoscopic surgery repair
I had the same type of surgery a few years back...the Doc put two choices on the table for me: laparoscopic or the old fashioned surgery with mesh. He encouraged the mesh even though it might take a bit longer to heal, but the complications would be fewer. I'm glad I took his advice. Got me up...- rowrd
- Post #9
- Forum: The Bear Pit
-
R
308 in 155 Scenar- Gassers Only Please
Out of an 18" OBR: 43.5 grs 4064 with 155 Sierra Palma Match.... and 43.5 grs Varget with 155 Berger VLD Hunting- rowrd
- Post #10
- Forum: Reloading Depot
-
R
Larue OBR 18"
Re: Larue OBR 18" Running a NF 50mm obj with an OBR mount on a 7.62 OBR also, but with a RISR option on the stock. Cheek wield and alignment has been good for me and those who have tried out the fit.- rowrd
- Post #69
- Forum: Semi-Automatic Rifles
-
R
Maggie’s Gotta love the welfare class...
Re: Gotta love the welfare class... Holy crap! I work in a McPharmacy and this vid nails the tip of the iceberg. "Whadda ya mean it's $X.XX? I'z donts pays for nuttin'!!"- rowrd
- Post #47
- Forum: The Bear Pit
-
R
La Rue OBR 7.62 18"
Re: La Rue OBR 7.62 18" <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: BCP</div><div class="ubbcode-body">If your brass is extremely hard to resize I'd have measured it...2500 rounds safely fired so it can't be dangerous but it could be on the edge of being out...- rowrd
- Post #30
- Forum: Semi-Automatic Rifles
-
R
La Rue OBR 7.62 18"
Re: La Rue OBR 7.62 18" <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Poison123</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: rowrd</div><div class="ubbcode-body">When I first started reloading for my...- rowrd
- Post #28
- Forum: Semi-Automatic Rifles
-
R
La Rue OBR 7.62 18"
Re: La Rue OBR 7.62 18" When I first started reloading for my OBR, I was worried that I would be able to use the brass only once. Resizing the once fired brass required a scary amount of force on the press to get it through the die, and sometimes only three-quarters of the case would get...- rowrd
- Post #23
- Forum: Semi-Automatic Rifles
-
R
OBR...she is a shooter!
Re: OBR...she is a shooter! I wish I could tell you what velocities I'm getting, but I don't a chronograph. Maybe I should change that. The 8208 meters easily and consistently through a Chargemaster, using Dar's instructions to decrease the throw time. I've also run some 175SMK over 42.0...- rowrd
- Post #42
- Forum: Semi-Automatic Rifles
-
R
OBR...she is a shooter!
Re: OBR...she is a shooter! I'd already posted in the reloading forum, but the 18 inch 7.62 OBR I'm using turns in nice groups with 41.5 IMR 8208 with 168 Nosler Custom Competitions. Not sure of the velocity, but five shot groups are consistently touching at 100 when the nut driving the...- rowrd
- Post #40
- Forum: Semi-Automatic Rifles
-
R
IMR 8208 XBR
Re: IMR 8208 XBR Using an 18 inch 7.62 OBR... I've been working with 41.5 grs 8208 / 168 Nosler Custom Comps in Winchester brass and 42.0 grs Varget/ 175 Sierras in same brass.. Don't know the velocities are, but I'm sure they're slow. I was looking for a consistent and accurate load at the...- rowrd
- Post #23
- Forum: Reloading Depot
-
R
What is your favorite Noveske .308 load?
Re: What is your favorite Noveske .308 load? Using 41.0 grs 4064 and a SMK 168.... Out of a Noveske 14.5 with a KX3 attached....a blooper load that gives great groups on paper...never chrono'ed it, but it's gotta be pretty slow.- rowrd
- Post #3
- Forum: Semi-Automatic Rifles
-
R
Reloading for OBR -Pressure Question
Re: Reloading for OBR -Pressure Question I've been reloading for my 18" OBR for the last few months, but have been staying at the lower end of the pressure and velocity side. What I've noticed in my particular rifle..others may be different.... VV140 (42 grs) and Sierra 175's (Winchester...- rowrd
- Post #7
- Forum: Reloading Depot
