• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by TackDriver2

  1. T

    seasoning the vudoo barrel

    It's a Caldwell BR Rock rest, but i changed out the cheap bullbag to the Protektor bullbag that fits the A5 McMillian stocks, I have a McMillian U1 stock on the Vudoo, its not the scope or the rings. ATACR 5-25 and the Badger rings are torqued at 65 inch lbs on the nuts and 18 inch lbs in the...
  2. T

    seasoning the vudoo barrel

    It's not quite consistent on the last few trips, it would shoot a nice cluster at 50 or 100, and then throw a little flyer and will not shoot the same tight group on the next few 5 shot groups and it would shoot tight again afterwards. I like consistency, I guess I need to break it in some more.
  3. T

    seasoning the vudoo barrel

    Well said.
  4. T

    Where to buy different lot # for Lapua and SK ammo

    Are there any ammunition depots where you can buy different lot # of Lapua and SK ammo for testing that sells 50 round boxes for each lot # instead of the 500 round box?
  5. T

    seasoning the vudoo barrel

    Vudoo 360 arrived earlier in the week, and I ran one wet patch of C4 and a few dry patches and she was ready to shoot those SK Standard Plus ammo. I bought two bricks of them, and so far on two trips I made to the range, I put 250 rounds total. Sighted in at 50 yards, my ATACR shows 5.5 MOA dead...
  6. T

    Vapor Trail bullets in Quickload?

    I could not find 6mm 103 Vapor Trail bullets in Quickload, does anyone have those bullets listed?
  7. T

    .300wm - .300wsm

    What is the model and name of that press? It looks cool.
  8. T

    PRS Talk Vapor trail or Barts bullets

    The Vapors shoots darn good as the Hybrids for me, during fireforming Lapua brass, it shot into the .1's @ 100 with virgin brass. Tested at 725 yards, shot into a 1.75 inch group on steel. After fireforming all 200 pieces, I redid the load development, added an extra grain of powder and shoots...
  9. T

    Best brass in consistency for 6 BR

    .1-.2 MOA or better @ 100, to be able to shoot 2 inches at 600 or better. I don't do PRS, I prefer benchrest. We shoot F class at 600 yards, but like shooting steel as well on my place.
  10. T

    Best brass in consistency for 6 BR

    I only have 100 pieces of Lapua 6BR brass atm, wanting to buy another 100 pieces, but not sure if the lot will match my current lot, since I want both batch to shoot the same POI at 600, so I may want to buy 200 pieces instead. I forgot what my old lot number was. I have always used Lapua brass...
  11. T

    6mm BR

    Lapua brass 105 Berger Hybrid Varget 30.2 grains BR4 primers 2823 fps ES 3 Just had a 600 yard match 45 shots / 3 strings of 15 shots @ 600 and measured under 4 inches ( counting wind and mirage )
  12. T

    .300wm - .300wsm

    300 Win Mag Lapua brass 200 ELD-X 75.6 grains RL-26 CCI250 primer .020" off lands - COAL 3.420" 26 inch barrel 3,075 fps
  13. T

    Range Report 105 Hybrid BC? Impacting high

    Checked as well, its 16 MOA on Berger website and yes there was mirage. Wind was from 3 o clock about 20 mph
  14. T

    Range Report 105 Hybrid BC? Impacting high

    Scope height - 2.12 Velocity - 2825 fps Firing direction to the East with 20 mph southeast wind Location is south Texas - 33' elevation Temp - 85 degrees / humidity 65% As for atmospherics, please define for me if above is not enough. I sent some images. Thanks
  15. T

    Range Report 105 Hybrid BC? Impacting high

    I did recheck the scope height and its spot on. Yes, the target was verified at 705 yards. If I lower the BC to .250, then its spot on, but its too much BC drop to justify why I'm getting that kind of drop. Even the velocity is spot on too. It's driving me nuts or is that Strelok Pro the issue...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts