- Thread starter pineoak
- Start date
I use 5 & 6 myself on my origins
I run #1. That knob would not clear on close in my 700sa standard Manners LRH molded bolt notches. Rather than clearance the LRH bolt notch as I don't think it would look right on that specific model, I moved those to EH1s that I clearanced. Been debating to see if there is a thinner knob to try (would need to be about 1/2 way through where it flares out before it reaches the first section of knurling on #1. #4 'looks' like it might be thinner there.
I'm really happy with #3, "helical diamond".
I only have one origin, but it's a beauty in 6mm ARC.
I only have one origin, but it's a beauty in 6mm ARC.
@pineoak since your question was pasted inside of my quote it wont let me quote you back but "Do you notice the difference in leverage/lift between the longer versus shorter?"
Yes, the longer is more leverage and lighter lift but I keep my pressures low enough and size my brass so that I dont lock my bolt up so neither are bad. I feel the constant sprung bolt head pressure against the action more than the brass extracting mostly.
Personally I like where the shorter puts the knob and its angled surfaces because my hands arent huge and it gives me a nice interface for when I open the bolt with my planted thumb and bladed fingers even if the lift is a smidge heavier. The long is perfectly fine as well but I do have to move my bladed fingers a bit further out from the rifle to hit the same angled area. So its purely where it hits me on the knuckle and how my thumb rotates that drives my preference for the shorter.
This is mainly all about when Im sitting on the bench by myself filling time, at a match it never crosses my mind.
A crude illustration of the difference Im talking about if you were to have the small and the large overlaid on one another
Yes, the longer is more leverage and lighter lift but I keep my pressures low enough and size my brass so that I dont lock my bolt up so neither are bad. I feel the constant sprung bolt head pressure against the action more than the brass extracting mostly.
Personally I like where the shorter puts the knob and its angled surfaces because my hands arent huge and it gives me a nice interface for when I open the bolt with my planted thumb and bladed fingers even if the lift is a smidge heavier. The long is perfectly fine as well but I do have to move my bladed fingers a bit further out from the rifle to hit the same angled area. So its purely where it hits me on the knuckle and how my thumb rotates that drives my preference for the shorter.
This is mainly all about when Im sitting on the bench by myself filling time, at a match it never crosses my mind.
A crude illustration of the difference Im talking about if you were to have the small and the large overlaid on one another
Last edited:
#2 for me. Have a #1 also I am and having a hard time getting along with it.
#2
#1 on all mine
What stock is thatI'm really happy with #3, "helical diamond".
I only have one origin, but it's a beauty in 6mm ARC.
I have #2. I can't say I don't like it but I would go 6 or 7 if I did it again. Not sure I would spend the money to switch since ther is nothing wrong with what I have
I got a Badger Ordnance with a 419 adaptor and like it a lot. #2 interfered with my KRG Chassis. I would have clearanced it, but I didn't really like how bulky it was anyway.
#1 on a Rimx; really like it.
Yup. Teardrop feels the best and is easiest for me to grab and run. Might not be the coolest looking, but it's the best operator.
I have 1&3. I like 1 much better.
419 bolt knob.
No. 2 here. Will probably try a 1 or 3 on the next one.
Have #3 on 6 TL3 and love it
#4 I like it because it is similar to my TRG.
1-2 on mine
I like the teardrop on mine
Played with a #1 this morning. It's a LOT smaller in person than it looks in the picture. I didn't find the texture to be overly aggressive, though it was definitely grippy overall.
I will play with a #4 sometimes on a build specific to small handed shooter in the family. Feels smooth and easy. I prefer the feel of the 4 with my XL glove sized hands to the #1.
I will play with a #4 sometimes on a build specific to small handed shooter in the family. Feels smooth and easy. I prefer the feel of the 4 with my XL glove sized hands to the #1.
#2 Tacticals on my TL-2's. Very happy with them.
Run tacticals with that guy on heres extension. Love it.
I had a couple custom ones made, very similar to Impact or Lone Peak bolt knobs. I also shoot those actions so like having the consistency between platforms.
