- Thread starter Sigma
- Start date
Found him, now I've just gotta make an account. Thanks.LoanHarvey on the other forum
PM me
Will the super trickler throw small charges, ike 4-15 gr? I use my V3 trickler for subsonic loads and found my groups have reduced dramatically.
That's something that's been at the back of my mind since ordering a V3 board for my V2 autotrickler. At least I still have my V2 board if that is to happen, but it's certainly something to think about.
What video? I didn't see any on the web site. Scrolled through the F Class John and didn't see it unless I missed it.
Obviously shims or some such shit missingFunny how the ATV4 obviously overthrows....
New Firmware 2.0
AI is much improved.
Also played around with manual mode... My settings below. Getting consistent 5-7 second drops with ease. Tweak as needed.
AI is much improved.
Also played around with manual mode... My settings below. Getting consistent 5-7 second drops with ease. Tweak as needed.
Loving mine so far. 2.0 is working great after a minor hickup that Peter worked out with me right away. The adjustability in incredible and the speed is great.
It's absolutely amazing to own and use a product where the creators listen to the users and reply back to emails with solutions, not excuses. Imagine that.
Last edited:
For those with a SuperTrickler .. Use this information as you want. This is just MY experience as a beta tester. 
V2 is good.
Install v2 firmware
Restore that powder profile
BEFORE you do anything, set the min and max trickle speed. Set the Min just so it's damn near trickling out spec after spec but with good speed, and max fast as possible till powder is almost coming out of pan.
Run the powder drops from powder restore WITH AI so it can learn the general setting parameters for you.... after about 40 drops, and if you feel like it's dropping consistently but with good speed, then turn off AI (ai might already have turned itself off by then)
Then, if you want, tweak the BULK, FINE, AND PULSE settings to fine tune consistency vs speed... and compare your settings with what AI was doing previously in regards to performance (consistently dropping powder vs speed = this is up to your preference).
The main goal of the supertrickler is to have AI do everything rather than you tweaking IMO.
If you feel you're not getting the performance you'd like, then repeat the above as AI WILL LEARN differently on the 2nd go around. The ultimate setting are your settings, and your settings only.
Hope this helps
V2 is good.
Install v2 firmware
Restore that powder profile
BEFORE you do anything, set the min and max trickle speed. Set the Min just so it's damn near trickling out spec after spec but with good speed, and max fast as possible till powder is almost coming out of pan.
Run the powder drops from powder restore WITH AI so it can learn the general setting parameters for you.... after about 40 drops, and if you feel like it's dropping consistently but with good speed, then turn off AI (ai might already have turned itself off by then)
Then, if you want, tweak the BULK, FINE, AND PULSE settings to fine tune consistency vs speed... and compare your settings with what AI was doing previously in regards to performance (consistently dropping powder vs speed = this is up to your preference).
The main goal of the supertrickler is to have AI do everything rather than you tweaking IMO.
If you feel you're not getting the performance you'd like, then repeat the above as AI WILL LEARN differently on the 2nd go around. The ultimate setting are your settings, and your settings only.
Hope this helps
I received my expected ship notice today of December 12th for order #569. 
I have it by Christmas. If anything I am more looking forward to it as reports come in.
I have it by Christmas. If anything I am more looking forward to it as reports come in.
Mine will also ship on 12/12. Super excited… I guess I should get my brass prepared.
I'm still 660. It will be Supertrickler #2. They're moving quick through orders. Good for them.
I’m 1084, hopefully it won‘t be obsolete by the time I get mine 
Y’all can always get in line for AT ver 5? Just sayingI’m 1084, hopefully it won‘t be obsolete by the time I get mine
I’m up there with you. By the time ours comes around it’ll have a titanium case, 100% spot on throws, and pull a perfect shot of espresso for those late loading sessions!I’m 1084, hopefully it won‘t be obsolete by the time I get mine
I’m curious if you know what optimization method they are using? For this kind of scenario I would assume it’s an optimization model like computing the Conjugate Gradient?
Totally worth the $$ too. The level of competition between various product lines has become really nice. Look at scopes over the last 4 or 5 years. Range finders. It has been fun to play with some high end stuff. Looking forward to next few years.
Order ~#550 shipped 4 days early.
Order #569 cleared customs 4 days ahead of promised ship day. Early Christmas for me this year...
Last edited:
What order # were you?
569 updated previous post too.
My delivery date of 12/14 just got pushed back to 12/16. Not bad.
Another user asked, but here are my settings for Varget. I get consistent 4.5 to 7 second throws with zero overthrows.
Version 2.00
If anyone is interested
Version 2.00
If anyone is interested
What order number are you? If you don’t mind me asking. Im in the low 600s and I don’t know how high the orders are at the moment going out.
~550
Thank you.
I noticed on the FB group that Rex posted order #600 will be shipping this week. My guess is you will be receiving an email soon.
I don’t have Facebook so I can’t see what’s new going on. I appreciate the heads up though.
That is the one thing I do not like about super trickler. I also do not have Facebook.
Wish they would periodically put up what number they were at on the site.
Not yet. I was going to ask here if anyone knew.
