I built this Wilson Combat AR 10 308 Super Sniper. 
How does it shoot. I've got a 20 inch ordered for a build that I just started , hope I choose a good barrel .
Haven't had time to try it out yet. I've been doing Chemotherapy Treatments for 2yrs and a couple of months, everything functions as should. Feeds rnds. cycling by hand and seems to eject them pretty good, I'm still debating on what scope to put on it. As soon as I get some time I'll take it out and run some down it and check function of it.
I would pay attention to your gas tube to gas key interface. At least in the past, Wilson places their rifle length gas port odd, halfway between Armalite AR-10 (15.5") and DPMS/AR-15 (15.125") length. They spec the longer gas tube, but some BCG gas keys will bottom out.
That's what happened on the first Wilson Combat Gas Tube, they gave a part number for the one that went with the Wilson Gas Block I ordered. I installed it and put the bolt in and it wouldn't mate up to the Bbl. Lugs, I scratched my head for awhile trying to figure out then noticed that the gas tube was more than half way in the cut out. The 2nd pic shows the bolt not matting up to the lugs with the Wilson Gas tube.
Pulled it out and measured it and sure enough it was long, did some research and got on line and went to White Oak and ordered two new ones, installed the White Oak Gas Tube that they recommend for that length of Bbl. and it worked the new Wilson Combat Nickel Boron Bolt that I bought with the parts made full engagement with the Bbl. 2nd pic shows full engagement of the bolt making full contact with the Bbl. Lugs 
I ordered the longer gas tube from Fulton armory, WC was out of stock, and ordered the tool craft bolt so I guess it's a toss-up if I've got the right one , wilson specs the longer tube for the supersniper 20 inch barrel , but it sounds like I might need a standard length, might as well order one as they aren't that much.
No they are different. I have the 18" Super Sniper 308cal Bbl. But under their listing for the Bbl. I bought listed the Gas Block, and the Gas Tube to go with it, but I had to order a different length Gas Tube cause the one they sent me was to long and bottomed out on the Bolt Gas Key.
The damage to that gas tube may be caused by vertical misalignment with the gas key. The offset of the gas tube required for a large frame is around 0.062" greater than a AR-15 when using mil-spec 0.750" low profile gas blocks. It may not seem like much of a difference, but can affect alignment. Almost all gas tubes are bent to the AR-15 spec, including those sold for AR-10/308. There are a number of exceptions to the above statement(s).
ETA: image
Finished my 1st LF AR 10 build today , Areo build kit , WC super sniper 20 inch barrel, wilson GasBlock ,Fulton armory gas tube & LPK , toolcraft BCG , presma CH ,Rise 1 SS 140 trigger , magpul moe stock & grip , dura mag mag , Vortex strike eagle 4x25 mrad scope , I'll take her to the range tomorrow for a test run , oh yeah 308 cal.
Attachments
Just finished up this build.
Still a few things left. Going to change to a Noveske rail, coat the barrel black and changing cans. Having the Omega 300 cerakoted coated black.
Haven't shot yet but soon.
Big block, Ascend Armory ambi receiver set
Geissele SD-E
15" Spikes rail, (new for sale, pm me)
6.5 CM Shilen 24" SS barrel, .936gb 1/7gt w matching bolt, RL gas
SLR agb
Geissele Buffer w braided spring
Geissele CH
Vortex 6-36 HD Razer G2
WMD Nib BCG
Still a few things left. Going to change to a Noveske rail, coat the barrel black and changing cans. Having the Omega 300 cerakoted coated black.
Haven't shot yet but soon.
Big block, Ascend Armory ambi receiver set
Geissele SD-E
15" Spikes rail, (new for sale, pm me)
6.5 CM Shilen 24" SS barrel, .936gb 1/7gt w matching bolt, RL gas
SLR agb
Geissele Buffer w braided spring
Geissele CH
Vortex 6-36 HD Razer G2
WMD Nib BCG
Amazing pic thread. Keep em coming. 
Who makes thermo fit dpms pattern AR 10 uppers?
I had one, it was my first Armalite. The first of 5 Armalites…I wished I still had it, I traded it with the idea of replacing it later. When you can find one the fetch a pretty penny. I was looking at one last week on Gunjoker and starting bid was $2200…
Hello,
Back story on mine is, originally bought mine in the early 2000's of an auction in new condition, kept it about 10 years, occasionally took to the range but not much. Along came a Smith Wesson Mountain Gun model 625 in 45 Long Colt. The guy that had it would not sell but only trade for my AR-10A2, So I regretfully traded and was sick over it a minute after the deal was done, but I had to have that Smith. Well it so happed that my local gun shop called me about a year later to tell me they just took my AR-10 it on trade and was giving me first chance at it. Needless to say I got it back and it will never again leave my safe. Best part of the whole story is when I bought it back I paid less then half of my original purchase price.
Back story on mine is, originally bought mine in the early 2000's of an auction in new condition, kept it about 10 years, occasionally took to the range but not much. Along came a Smith Wesson Mountain Gun model 625 in 45 Long Colt. The guy that had it would not sell but only trade for my AR-10A2, So I regretfully traded and was sick over it a minute after the deal was done, but I had to have that Smith. Well it so happed that my local gun shop called me about a year later to tell me they just took my AR-10 it on trade and was giving me first chance at it. Needless to say I got it back and it will never again leave my safe. Best part of the whole story is when I bought it back I paid less then half of my original purchase price.
Upper:
Stag Stripped Upper
V Seven BCG
Radian Raptor SD
Proof 18”
SF Brake
Odin Gas block adjustable
SLR Handguard
NF 2.5-20 NX8 with adm mount
SF Sps-300
Lower:
LMT Mars-H
Larue Trigger
PRS lite
Stag Stripped Upper
V Seven BCG
Radian Raptor SD
Proof 18”
SF Brake
Odin Gas block adjustable
SLR Handguard
NF 2.5-20 NX8 with adm mount
SF Sps-300
Lower:
LMT Mars-H
Larue Trigger
PRS lite
NICE
how do you like the Centurion Arms handguard?
18" Criterion stainless 6.5 CM barrel in a SMF tactical upper receiver, URX4 handguard, Larue MBT-2s. Weight is 9.5 lbs but another 10 oz or so can be shaved with a lighter stock. I shot some 105 grains through it the other day and it was a blast. Very soft shooting, feels almost like an AR15.
Aero M5 receiver set
Aero rail
Aero lpk/buffer/tube/spring
CMC 2.5lb single stage trigger
Toolcraft carrier with JP enhanced bolt
Faxon Big Gunner 18” 308
Dead air md
Aero agb
Warne qd bipod
Trijicon Tenmile 3-18x50 in adm mount
Still dialing everything in, but man do I love shooting this gun!
Aero rail
Aero lpk/buffer/tube/spring
CMC 2.5lb single stage trigger
Toolcraft carrier with JP enhanced bolt
Faxon Big Gunner 18” 308
Dead air md
Aero agb
Warne qd bipod
Trijicon Tenmile 3-18x50 in adm mount
Still dialing everything in, but man do I love shooting this gun!
Attachments
This one weighs in at It's got a Krieger 20" custom m110 profile barrel in 6.5 CM, Rifle +2, SA adjustable bleed off GB, 15" URX4 handguard, SMF TAC-10 upper receiver (Armalite / SR25 pattern / slant cut), LMT BCG, Larue complete lower, topped with TT315M.
14.69 pounds with bipod and loaded 20-rd mag. She's the heftiest rig in my arsenal.
14.69 pounds with bipod and loaded 20-rd mag. She's the heftiest rig in my arsenal.
KAC BUIS
KAC receiver ext. kit and LMT SOPMOD
Geiselle SSA-E
AAC SDN-6
ATACR 4-16x42 with Spuhr SP-4016
Nice. What's she weigh? Mine above is at about 14.60 pounds loaded out.LMT MARS-H w/ 20” SS barrel
KAC BUIS
KAC receiver ext. kit and LMT SOPMOD
Geiselle SSA-E
AAC SDN-6
ATACR 4-16x42 with Spuhr SP-4016
At 18.9lbs this is a pig!
Attachments
This 24" Bull will make you think anything sucks, Always go with a big profile as it makes the rifle that much more stable
Attachments
Finally updated my 6Creed build and it is complete.
PSA upper & Lower
Magpul PRS Light stock
SGT of Arms 17.5" ARCA forearm
ERGO Grip
Rainer Arms Match 22" 6 Creed barrel +2 gas
SA Adjustable gas block
PTP Master Chief Suppressor
Pulsar Thermion DUO optic.
This is my primary predator rifle.
PSA upper & Lower
Magpul PRS Light stock
SGT of Arms 17.5" ARCA forearm
ERGO Grip
Rainer Arms Match 22" 6 Creed barrel +2 gas
SA Adjustable gas block
PTP Master Chief Suppressor
Pulsar Thermion DUO optic.
This is my primary predator rifle.
Nice. Match or "Ultra Match" barrel? And how does it shoot?
it is the Match Barrel. with 103 ELDX factory loads its right at 1.5 for 5 at 200y. I have some hand loaded 75g Max's & they shoot just a tic under 1.5, but in the 3450 fps range. I can't complain with either load for deer or predators.
My first full .308 build.
- Aero Precision Builders kit w/ matching Magpul stock/grip
- Aero BCG, gas tube & adjustable gas block
- Faxon Duty Series 18", Big Gunner, .308
- Larue Trigger
- VG6 Gamma muzzle brake
- Primary Arms SLx 4-16x44 FFP Rifle Scope - Illuminated ACSS HUD DMR Reticle - Magpul bipod
- NY compliant mag lock (replaced pictured mag w/ 10 rnd)
Grouping at 100yds shown from initial zero
First time out it shot flawless and cycled great.
Recently took it to the range and had a bunch of FTF/failed cycles, don't think the bolt was going far enough back to pick up the next round - unfortunately i didn't bring the long Allen key to the range, going to go back again and run it wide open, see if that solves the issue. -
Edit: just was doing some digging on these forums and one issue I have is the charging handle runs into the cheek riser - apparently this happens if you use a Magpul PRS intended for a Ar15 with an AR10 platform.
Also read about an issue with the stock screw being too long (from a post from 2011, any idea if this issue was resolved?)
- Aero Precision Builders kit w/ matching Magpul stock/grip
- Aero BCG, gas tube & adjustable gas block
- Faxon Duty Series 18", Big Gunner, .308
- Larue Trigger
- VG6 Gamma muzzle brake
- Primary Arms SLx 4-16x44 FFP Rifle Scope - Illuminated ACSS HUD DMR Reticle - Magpul bipod
- NY compliant mag lock (replaced pictured mag w/ 10 rnd)
Grouping at 100yds shown from initial zero
First time out it shot flawless and cycled great.
Recently took it to the range and had a bunch of FTF/failed cycles, don't think the bolt was going far enough back to pick up the next round - unfortunately i didn't bring the long Allen key to the range, going to go back again and run it wide open, see if that solves the issue. -
Edit: just was doing some digging on these forums and one issue I have is the charging handle runs into the cheek riser - apparently this happens if you use a Magpul PRS intended for a Ar15 with an AR10 platform.
Also read about an issue with the stock screw being too long (from a post from 2011, any idea if this issue was resolved?)
Attachments
Last edited:
If you still have problems after you adjust the AGB, it might be best to start a new thread. Until then, check into your gas tube length and action system.
Somewhat relevant thread:
https://www.snipershide.com/shootin...roblems-is-this-over-or-under-gassed.7197411/
Aero M5
Aero Nitride BCG
Magpul SL-S stock
Magpul Moe+ grip
Warhammer Mod2 Micro CH
Hiperfire EDTSS trigger
Lancer smoke 20rd mag
Wraith 4k mini scope
Weighs 12lbs as seen here
Aero Nitride BCG
Magpul SL-S stock
Magpul Moe+ grip
Warhammer Mod2 Micro CH
Hiperfire EDTSS trigger
Lancer smoke 20rd mag
Wraith 4k mini scope
Weighs 12lbs as seen here
Last edited:
Well I got the itch for another large frame AR, I've been putting this Zev together for awhile and in the mean time came across this sweet LMT for sale. I just had to have both. I was going to make the Zev a .308 and have the barrel dimple fluted by Marvin Pitts. While I was waiting to receive that barrel from Marvin, I bought the LMT .308. So I decided to put this Criterion 16 inch 6.5 Creedmoor barrel in the Zev and use the dimpled .308 barrel for the LMT and get rid of the factory LMT barrel. Just waiting to get the dimple barrel back from D. Wilson. I can't wait to have them both finished and head to the range.
The Zev build is cerakote H-250 to match the B5 Coyote brown.
The Zev build is cerakote H-250 to match the B5 Coyote brown.
Contact Noreen Firearms in Mt.
131 Jetway Dr, Belgrade, MT 59714
(406)388-2200
I'm still waiting for my .338 lapua, it's stint the manufacturing process
131 Jetway Dr, Belgrade, MT 59714
(406)388-2200
I'm still waiting for my .338 lapua, it's stint the manufacturing process
Here's what they have:
BN36X3 - Long Range (300 Win Mag | 7mm Rem Mag)
$3,495
VIEW PRODUCT
Belgrade, MT 59714
(406) 388-2200
https://www.instagram.com/p/C2uvxWAr-ku
BN36X3 - Long Range (.30-06)
$2,795.00BN36X3 - Long Range (300 Win Mag | 7mm Rem Mag)
$3,495
VIEW PRODUCT
Subscribe to Our newsletter
EMAIL ADDRESS *About Noreen Firearms
131 Jetway Dr.Belgrade, MT 59714
(406) 388-2200
https://www.instagram.com/p/C2uvxWAr-ku
My last summers "blue light special" build (found all parts on sale over a few months). After fighting the Faxon barrel I had for way too long, gas block machined in wrong spot, breach not machined right, sent that back and went with Black Hole Weaponry barrel, my test and sight in it operated flawlessly.
-308
-Aero M5 upper and lower set. (aero parts kits)
-Barrel - Black Hole Weaponry 18" SS rifle length gas system
-Rubber City Armory BCG
-Larue MBT 2-stage
-Buffer - Armaspec stealth BB 5.7oz Gen 4
-Gas Block - Riflespeed adjustable & tube (its beyond awesome)
-Charge handle - Firehog Mod-Gem4 ambi charging handle with gas exhaust (All they had was blue, and it was only $20.)
-Muzzle brake - Strikes Jcomp gen 2 compensator
-Optic - Vortex Strike Eagle 3-18x44
-AIM Sport hand guard, Magpul STR stock, Magpul K2+ grip,
-Weighs 11lbs , 15oz w/o mag.
-308
-Aero M5 upper and lower set. (aero parts kits)
-Barrel - Black Hole Weaponry 18" SS rifle length gas system
-Rubber City Armory BCG
-Larue MBT 2-stage
-Buffer - Armaspec stealth BB 5.7oz Gen 4
-Gas Block - Riflespeed adjustable & tube (its beyond awesome)
-Charge handle - Firehog Mod-Gem4 ambi charging handle with gas exhaust (All they had was blue, and it was only $20.)
-Muzzle brake - Strikes Jcomp gen 2 compensator
-Optic - Vortex Strike Eagle 3-18x44
-AIM Sport hand guard, Magpul STR stock, Magpul K2+ grip,
-Weighs 11lbs , 15oz w/o mag.
Last edited:
Similar threads
