Dont buy them. Buy Hornady match 6.5 CM dies. Twice the quality for half the price. You’re welcome.
Having used both I have to say “what you smokin’ boy?”Dont buy them. Buy Hornady match 6.5 CM dies. Twice the quality for half the price. You’re welcome.
Ive owned a lot of Redding(thousands of dollars worth). I’ve taken castings of them, looked at them under magnification, compared them directly with their competition, and it’s not even close. Only thing they have going for them is a big cartridge menu, otherwise they're just overpriced mediocrity.Having used both I have to say “what you smokin’ boy?”
Really taken castings of them looked at them under magnification? Crap i use them they seem to work. Maybe a little expensive. I do prefer Forster. Sombody slap me .Ive owned a lot of Redding(thousands of dollars worth). I’ve taken castings of them, looked at them under magnification, compared them directly with their competition, and it’s not even close. Only thing they have going for them is a big cartridge menu, otherwise they're just overpriced mediocrity.
Edit: Any chance you had custom grade and not match grade hornady’s? I’d agree with you then.
Ok why a expander mandral?Redding is great for the price. Buy with confidence. Get a s type bushing die and an expander mandrel and you are set.
Ok why a expander mandral?
Theres lots of talk about these dies.
I am reloading for the 6.5cm and loading from a detachable magazine.
What die set do I want and why? If you can supply the part number from redding as well it would be great so I can place an order.
First it started with finding dies that actually matched the chambers well. .308 and .223 (what everyone was shooting back then ) are all over the map, and some dies weren’t a good fit. After you end up with a few different sets of dies in the same caliber, you can’t help but ask yourself why the Redding’s are so sensitive to lube, take so much effort, and leave shiny spots on your cases. Casting the dies ruled out dimensional issues. It’s because their internal finish sucks. It sucks across all cartridges as well. The Hornady sizers are dimensioned well, and their internal finish is very nice, for about half the cost.Really taken castings of them looked at them under magnification? Crap i use them they seem to work. Maybe a little expensive. I do prefer Forster. Sombody slap me .
Just wondering i dont use a expander ball or a mandrel. I fond i get excessive runout with both. Could be me im not a expert or perfectBecause it better uniforms the inside of the neck. Which is what matters more because that’s what contacts bullet. Along with being better on brass than dragging expander ball through it.
Ok probability of why i get 3 die sets before i can make good rounds. In that case i have better luck with forster then redding then rcbs nope struck out 3 times with hornady never got good dies with them .First it started with finding dies that actually matched the chambers well. .308 and .223 (what everyone was shooting back then ) are all over the map, and some dies weren’t a good fit. After you end up with a few different sets of dies in the same caliber, you can’t help but ask yourself why the Redding’s are so sensitive to lube, take so much effort, and leave shiny spots on your cases. Casting the dies ruled out dimensional issues. It’s because their internal finish sucks. It sucks across all cartridges as well. The Hornady sizers are dimensioned well, and their internal finish is very nice, for about half the cost.
If the OP must blow $170-200 bucks on a seater and a sizer, buy a Whidden sizer and a Forster seater.
So what issues were you having with them?Ok probability of why i get 3 die sets before i can make good rounds. In that case i have better luck with forster then redding then rcbs nope struck out 3 times with hornady never got good dies with them .
Getting to much runout i just got new die sets or seating dies till the problem went away started with good new brass so that wasn't the issue.So what issues were you having with them?