Search results

  1. OLD308

    Henderson Precison

    Yea emails are short and abrupt, but if ya get on the phone with Todd you will see why. Todd will not let you go till everything is crystal clear and your happy. Great customer service. Great product. Don't know what a Gen 3 would improve on other than the case length set up.
  2. OLD308

    223 Component Recommendation Pls

    PM me if I don’t hit ya back latter. Jon cut my Accurate Mags to fit and feed perfection.
  3. OLD308

    Talk me into or out of an auto trickler v3

    "I'll give you my V3 when you pry it from my cold dead hands" Charlton Heston quote, sorta, but ya get the point.
  4. OLD308

    Factory Ammo Recommendation for 6.5 Creedmoor 1/8 twist barrel

    Sellier and Bellot 140 FMJ BT was $11 a box here before the global economic restructuring. 6" steel target at 500 yards all day with every 6.5 rifle I've had out here. To include a Bergara Pro and HMR. Is it Berger quality? Hell no! But its factory ammo thats cheap and shoots. Hope this helps.
  5. OLD308

    223 Component Recommendation Pls

    Hawk Hill 1-7 M40 24" Beanland Custom Rifles build cut for 80.5 bergers Lapua Brass Berger 80.5 205 primers Varget "nightmare" powder. First jug (8lb) was 24.4, second jug (8lb) is 25 even for same velocity. Yep, ya read that right. .6 grain difference for same velocity. Both jugs were tested...
  6. OLD308

    Case trimmers set up advice

    They are sold. I bought them for the stuff I don't shoot as much so as to avoid altering my Henderson trimmer. Setting up the blades on the Trim it 2 was a PITA. There was so much play in the caliber dies that a consistent trim length is impossible. To my standards anyway. More than good...
  7. OLD308

    Flat back more stable then boat tail

    The smallest, easily repeatable, supersonic loads, for paper punching only, have always been flat based bullets for me. The .308 150 Berger flat based match bullets for inside 500 yards are astounding. Supposedly, there is a better/uniform seal at the rear of the bullet. Think rebated boat...
  8. OLD308

    Closed

    Thread closed. Thanks for looking.
  9. OLD308

    Closed

    Sorry I neglected this post for so long. Should have updated a while ago. Keep your chins up! Dreams do come true. Just at a higher rate for Vudoo owners. Thread closed.
  10. OLD308

    Old Mag Identification

    No one remembers these? No response from Seekins, guess I’m just SOL.
  11. OLD308

    Tips on fine tuning the primer seating process on Dillon 550

    Uniquetec has the answerers to your issues. And cutting out the crimps. I use a primer pocket uniformed.
  12. OLD308

    Austin TX long range shooting

    Nope, not a member. Just a place a group of us used to meet up at one a year.
  13. OLD308

    Austin TX long range shooting

    Austin Gun Club. Shot the mile target out there many times. Don't go there anymore due to the drive.
  14. OLD308

    Best $2k rifle?

    One of the 4th of July ARC rifles. That was and is the best 2K 6.5 CM rifle deals. Just happen to have an unfired one setting here. If your looking...
  15. OLD308

    What are you guys doing for trimmers these days?

    Yep Had a Giraud for about 5 years. Switched to the Henderson. Sticking with the Henderson. A lot of trimmers are fast. A lot of trimmers are consistent. But only 02 trimmers are fast and consistent. Giraud if you like shoulder based measurements. Henderson if you like over all length...
  16. OLD308

    308 shooters

    2900 with 155 is a cake walk for a 22” barrel. Benchmark or 8208XBR will get you there if you do your part. Unless you have an oddball variable, there should be no pressure signs. Hope this helps.
  17. OLD308

    Netflix's Project Power

    Yep, I want the time back.
  18. OLD308

    Marksman and long range courses

    Contact @Hogstooth. He’s in the Weatherford area. Facility is top shelf, instruction is spot on, rates are ridiculously low for what is provided. You will not be disappointed.
  19. OLD308

    Smiths for barrel threading for suppressor

    Beanland Custom Rifles. Not knocking others, “they” have made me some great rifles. Jon is just a different animal. Turn around time reflects his demand (high). He is a one man shop. If you call, you will hear him working on rifles while speaking with you. All work is done by him from start to...