Search results

  1. F

    Turning an AR10 barrel from a barrel blank

    Misery Custom Rifles does them all the time. www.miserycustomrifles.com
  2. F

    Night Vision Trijicon Snipe IR vs IRAY RH25 for clip on

    Sounds like the RH25 is the way to go?
  3. F

    Night Vision Trijicon Snipe IR vs IRAY RH25 for clip on

    I tried googling this and couldn't find a comparison. Does anyone have experience using both of these thermals strictly as a clip on in front of a day scope? Thought I was set on the RH25 until I saw the Snipe IR. Once again, strictly as a clip on in front of a day scope. Any thoughts?
  4. F

    22 creedmoor

    3265. Primers looks good, but getting ejector marks. I was using hornady 6 creed large rifle primer brass before and I think I was hitting pressure around 41.0. Are guys running 43-44 grains running super long freebores?
  5. F

    22 creedmoor

    How are guys running 42, 43, 44 grains of H4350 with a 75 eldm? I'm shooting a 20" bartlein 7.7 twist with a .080 freeborn and a .257 neck. This puts the neck shoulder junction at the start of the bearing surface of the 75's and a .010 jump. I'm hitting pressure at around 39.5 H4350 in...
  6. F

    ISO new or a Smith for LMT MWS barrels

    https://miserycustomrifles.com/
  7. F

    22 Creedmoor gas gun trials and tribulations

    Any issues with the long skinny bullets jamming into the feed ramps and not feeding? Did you happen to try any bergers for feeding?
  8. F

    .375 Cheytac brass vs reamer base dimension

    Measured with a micrometer. It is PTG, so there is that. If I get the reamer reground to Peterson brass specs, what do I do for headspacing? Is .015 an exact difference between Peterson and cheytac? Should I cut .015 short of a cheytac go guage? Thanks for the help.
  9. F

    .375 Cheytac brass vs reamer base dimension

    Peterson brass measures .633 at the .200" mark at the base and my reamer is about .6395 at the .200" mark. There seams to be different specs on the Cheytac all over the place. Is this .0065 bigger base going to cause issues with brass expanding that much at the base? What are you guys using...
  10. F

    22 Creedmoor twist rate

    Anyone spinning .224 bullets fast with some good or bad advice?
  11. F

    22 Creedmoor twist rate

    I have built a few .22 Creeds on 8 twist 5R Bartlein barrels and they shot great. I am looking to build another one and can't find an 8 twist #13 anywhere in stock. I am looking to strictly shoot 75 elm's out of this and I know the 8 twist is the way to go. I can find 7.7 and 7.5 twist, which...
  12. F

    Gunsmithing Beretta apx carry problems

    Playing with it a little more and looking into opening at the back it appears when I pull the trigger the striker isn't able to move freely like it should, it hangs up on the slide and that's what cocks the slide. It took the slide off and if I put some pressure to the right side, I can get the...
  13. F

    Gunsmithing Beretta apx carry problems

    That makes a lot of sense. Thank you for the big write up. So what would be out of spec to cause this? Replace the striker block?
  14. F

    Gunsmithing Beretta apx carry problems

    A buddy brought me his apx carry because it doesn’t even fire. He said there might have been some trigger parts swapped out on it but can’t get ahold of the guy who did it. What’s happening is if you lower the slide slowly it won’t go into battery. If you drop it, it will usually close all the...
  15. F

    Custom AR Builder Near Montana

    Misery Custom in Bozeman. https://miserycustomrifles.com/
  16. F

    LMT .308 MWS

    Yes, in my experience the duel ejectors on the AR10 bolts throw a completely different (and more reliable) ejection pattern than single ejectors that are commonly seen on ar10's.
  17. F

    LMT .308 MWS

    Ive had this before as well. Way over gassed and the rounds aren't being pushed up fast enough for the bolt moving forward and end up chewing up the front of the mag. Your not seeing it on the KAC mags because they are metal and possibly slightly lower cut so the nose can clear. Heavier...
  18. F

    LMT .308 MWS

    Letting this 16" Bartlein go. PM if interested.
  19. F

    Replacement buttpad for Magpul PRS gen3?

    I would also like to know, the length of pull on those gen 3 prs’s is way too long on an ar10 for my short self.