Search results

Search the forum Search Articles
  1. B

    Gunsmithing Who installs Badger bolt knobs?

    Re: Who installs Badger bolt knobs? www.kampfeldcustom.com
  2. B

    Problem with Stiller Tac 300 action

    Re: Problem with Stiller Tac 300 action A crater won't ruin the trigger, just if you blow or pierce a primer it is possible. The pressure coming back through the bolt body can blow the cocking piece back resetting the trigger. When it slams back forward under spring pressure, it can break...
  3. B

    Gunsmithing Cerakote Application

    Re: Cerakote Application Just like you said edief. I degrease then blast and blow off. I then shoot the cerakote and then bake. I never have any problems with oil or anything doing it this way. Same finish every time. If the oil creeps after it bakes a little it never causes any problems...
  4. B

    6x47L accuracy???

    Re: 6x47L accuracy??? Yea, I've been wanting to try those too. The 123's sure shoot good in my 6.5x47.
  5. B

    6x47L accuracy???

    Re: 6x47L accuracy??? Lee, I'm shooting 40.7 gr. of 4350 @ 3100 fps. with the 105's. Most people are running between 39 gr. and 40.8 of h4350. I would start at the bottom end and work up. When i shot the 115's i used about 1 to 1/2 grain less powder (h4350). I really have not tried any...
  6. B

    Rifle Scopes Quick 'n Dirty review of the Zeiss PRF LRF

    Re: Quick 'n Dirty review of the Zeiss PRF LRF If you will look at the specs, the Zeiss PLRF has one of the largest beams, unlike the 10x45 RF's. They have one of the smallest. The beam divergence on the PLRF's measure 4x2 milrads where as the beam divergence on the RF's measure .5 x 1.5...
  7. B

    Gunsmithing Stainless Barrel coating.

    Re: Stainless Barrel coating. Use not chlorinated brake cleaner. I use it all the time. No residue. or acetone as suggested earlier. I usually spray with the brake cleaner, then go strait to the blast cabinet. I then just blow of with air and cerakote.
  8. B

    Wyatt's .308 Detachable Magazine Assembly

    Re: Wyatt's .308 Detachable Magazine Assembly Figured out what the problem is. The island for the adl guard screw on a stiller tac 30 is .500 wide compared to remingtons .300 wide. You can't slot the magazine any wider at the back to fix this. You have to mill the island to .300 wide about...
  9. B

    Wyatt's .308 Detachable Magazine Assembly

    Re: Wyatt's .308 Detachable Magazine Assembly I don't have any pics. I ordered three of these units. I sent one to a buddy of mine who is a smith in okc. He told me about this problem trying to install it in his own action. I can tell you that if he says it wont work without mods, it...
  10. B

    Wyatt's .308 Detachable Magazine Assembly

    Re: Wyatt's .308 Detachable Magazine Assembly could you explain how these issues are taken care of. I just got this bottom metal two days ago from wyatts. The back of the clip will not go up in the port. It hits in the back of the opening just in front of the adl magazine screw hole. On...
  11. B

    Wyatt's .308 Detachable Magazine Assembly

    Re: Wyatt's .308 Detachable Magazine Assembly Tried one of these today on a stiller tac 30 and it would not drop in. The bottom magazine port is not cut far enough back. I can't see how it will work on a remington either without milling out the rear of the port. It worked fine on the...
  12. B

    Stiller Action in a AICS stock

    Re: Stiller Action in a AICS stock I actually think that is the only way that they come. The 223 bolt face makes no difference. It will work fine. They only way that you would need a different combination is if you were trying to convert to the AW mags. You would have to remove the feed...
  13. B

    Stiller Action in a AICS stock

    Re: Stiller Action in a AICS stock You don't have to have a DBM model. I just finished putting a BDL model in a aics stock. That is with the standard AI mags. If you use the AW mags, You will have to have a DBM model without the feed rails. You may have to inlett under the bolt handle...
  14. B

    Problem with Surgeon Round action bolt timing?

    Re: Problem with Surgeon Round action bolt timing? I have seen quite a few of those round actions including their standard action and they are all that way. They leave more clearance in these areas than other action manufacturers for dirt, sand or grime. If you don't believe me, just call...
  15. B

    Problem with Surgeon Round action bolt timing?

    Re: Problem with Surgeon Round action bolt timing? i would not worry. Surgeon designed them this way. I'm pretty sure that's the way there meant to be for purposes of shooting in dirty environments.
  16. B

    Badger M2008 Builds.....Where are they?? Pics...

    Re: Badger M2008 Builds.....Where are they?? Pics who did the multi cam on the a-5 stock?
  17. B

    Surgeon round inlet question

    Re: Surgeon round inlet question Lee, the rear tang is a little wider but i don't think that will cause much problem. The biggest problem is the ejection port on the side. The surgeon comes just a little further back than the remington is inletted for. You have to lengthen the ejection...
  18. B

    Rifle Scopes Seekins Rings

    Re: Seekins Rings You can't beat service like that. I still think you have the best rings out there. Thank you.
  19. B

    Rifle Scopes Seekins Rings

    Re: Seekins Rings yes, they are binding the same way. i have to remove the screws to get them to release from the rail. They are on a surgeon with a built in rail. I have another set that does not do this. I am going to send them back. He will take care of them.
  20. B

    Rifle Scopes Seekins Rings

    Re: Seekins Rings I got a set of 34mm rings recently. They are doing the same thing.
Top Bottom
Back
Home
Forums
Merch
Alerts