Search results

So where is all the Winchester .308 brass? Lapua and just about everybody else is readily available but not Winchester brand .308. Anybody know why and where some may be hiding?

I've been formulating my own thoughts here and I like the SLR Solo Lite. Seems rigid and super light weight. Not quite sure about KMR however. For those that have the two or have real experience with the two or can compare the two...Which do you think is better having shot and handled both...

Guys perhaps you can shed some light on an issue a friend and I are having. I bought a Krieger 7.7 spr profile barrel spun and chambered by Compass Lake with their CLE reamer. I got the barrel torqued to approx. 35 ft.lb. in a vltor receiver with a NSR rail. Lower is noveske with a two...

I have searched and searched. I cant find it. Can someone help out here? Thanks!

Hey guys, Can anyone tell me for certain if a Marlin 783 .22WRM rifle originally came with any type of fill in the lettering? Prob would have been somewhere 1975-1980.... Any pictures would be great.

I'm looking to have a stripped upper, lower, receiver extension tube, and troy alpha rail cerakoted in one color...either magpul flat dark earth or troy dark earth. Anyone have any recommendations for someone who does quality work with about a week turnaround time?

Ran out of them and I cant find a base to ogive measurement on the Hornady 75 BTHP/OTM (T1C) anywhere. If someone could come up with 3-5 measured bullets. Thanks.

So I'm loading up some match ammo for a new AR platform... .223. Take some headspace measurements from once fired brass from the new rifle. I start full length sizing the brass and bumping the shoulder .002" back. It's set up to be a precision rig so I figure .002" is just right while still...

I'm loading for a new noveske 18" spr rifle with 77smk. Ive tried a little Tac and Varget. No luck yet. I know it shoots cause I got a .4" group with Hornady 55TAP. Anybody have a go to load with their Noveske chambers?

I would expect the complete rifles they build are water tight when it comes to fit. But... How about buying an upper and the getting a stripped lower built out. Anybody have any experience with building out a lower and mating it up to thier uppers? Fit and feel?

I've been looking at Noveske, Ranier's ultra match, BCM, and a few other 18" SPR type barrels for a build. 1/8 twist would be first choice but 1/7 would be fine also. Looking to shoot only 75bthp and 77smk or some of the Bergers in the 70s. Also looking for the best upper receiver money can...

Switched over from a 10.5" DI setup that ran flawlessly on my CQB to the 12" piston kit. It ran fine for approx. 100 rounds. Cleaned it then experiencing a failure for the bolt to lock back on the last round most of the time...but varies according to lubricationit seems. This only occurrs with...

I also posted this in the semi-auto section with no responses...perhaps it is better placed here. Here's the setup: ADM mount-1.47" ring height Vortex 2.5-10x44- bell diameter 1.63" Which leaves approx. .660" clearance from the bottom of the bell to the picatinny rail/top of upper. I can't...

Here's the setup: ADM mount-1.47" ring height Vortex 2.5-10x44- bell diameter 1.63" Which leaves approx. .660" clearance from the bottom of the bell to the picatinny rail/top of upper. I can't seem to find the height of a folded MATECH BUIS. If any one knows this dimension or running this...

I bought a new T1. Never fired it, but fingered it here and there. I got to looking at the dot closer. It seems the dot isnt really a dot but more of two goofy lines that spand approx. 3" at 15 yards. The lines run from the 10oclock to the 4oclock position. First aimpoint product for me and...

What are the sizes of each of these dots on this TA11H ACOG reticle? I cant seem to find the answer anywhere.

I'm trying to avoid battery drain or bursting. What's the correct way to lay batteries on top of one another in a stock tube? Pos to pos, neg to neg, or pos to neg???

Looking for some advice from the PROs on IR aiming lasers, IR illuminators and so forth. The laser defense mfg TLAD has been referred to as a Chinese knock off of a BDAL-A2 so I have read. I tried to fo my research on these but the information/posts/reviews I found on these was over a year old...

Hey fellas I need a little help figuring out what type of handgaurds these are and how he texture was obtained. I found these pictures on m4carbine.net towards the end of the mrp thread. Looks like tangodowns and knights but with a special texture. Im not a member there otherwise I would have...

I'm looking for some pointers on getting these .30 Barnes rounds going. I have two different weights in two different platforms. I am looking to get the most on velocity with only sacrificing very little accuracy and I'm not quite sure on the powders that will get me there considering my short...