Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Watch Out for Scammers!
We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!
I have a few pistols and a sub-sonic only 300Whisper AR that I want to use an IR laser pointer on. The normal pistol ranges will be 25 yards max and the normal 300w range is 50 yards with some shots at 100 yards. I have seen the pics of the .7mw IR lasers and at25 yards they about cover an 18"...
I just picked up some used 338L brass and half of it is loaded with unknown components. I want to break it down but the round is too fat to fit in my RCBS kinetic bullet puller. Any suggestions as to how to pull the bullets without messing them up? Thanks
I have a Stiller single shot action that is a duplicate of a Rem 700 Long Action. If I get a new bolt or perhaps my 308 bolt face modified, can this be used for a 338 Lapua? Or is there a special magnum action required. Thanks
Can I use the 3x screw in front lens for the PVS14 and an Aimpoint? How will it work? Will it be as good as a D740 or M845? Will it all fit on a standard AR flat top? Thanks
If I order a brand new AI AE MKIII in 6.5 Creedmoor will it come with a miss timed AINA marked barrel or will they perfectly fit a barrel with correctly timed caliber and AINA markings? I dont have a problem with the replacement barrels and would love to have one, but my club has a varmint...
I just got an AI AE MK I in 308 with 24" barrel. I have never handled an AI before this so I have nothing to compare it to. I like this rifle so much I can not put it down. I have had it to the range 5 times in 10 days. It shoots better than my expectations. I do have a couple questions though...
on an all original AI AE .308 24" with the factory installed picatinny rail - will a NF NXS scope with 56mm objective fit using 1.00" high rings? Thanks
I have a tikka t3 sporter in 6.5x55. I load a 140 amax over 48.5 grains of h4831sc in lapua brass. It shoots great, 24" barrel. I dont have a chronograph but have done a lot of research and was guessing my velocity at around 2800 I zeroed the other day at exactly 100 yards, dead nuts on, and...
I have a FN SPR bolt action 308 with detachable 4 round magazine. I want to change it to a conventional hinged floor plate with magazine follower & spring. Will the factory FN floor plate swap right in to my rifle? Will the factory follower work in my receiver? And if so, does anyone know a...
For anyone with direct experience with the 5-25x56 PMII and both mil and moa turrets... Is the spacing of the incremental clicks farther apart on the MOA turrets? Or are there the same number of clicks per revolution but they are just graduated in MOA instead of mil? Thanks
I just bought a S&B PMII 5-25 DT mil/mil. The manual says the internal elevation is off set by half of the total elevation so I assume this means 7.5 mils??? My question is, will I be able to go down enough to get a 100 meter zero with a 20 moa rail? Also, does this mean I have 22.5 mils of...
I am getting a pvs-14. I will be using it on a few different rifles. I will also get a mil spec 3x for it. On one rifle I am thinking of just a red laser and the pvs-14 with 3x. Will the red laser be too bright? Is there a civilian option for an adjustable intensity red laser? What is the...
Years ago I bought a Leupold scope with tall target knobs. It came with 2 sets of knobs - one set that used the screw on dust covers and another set that was a little over size and did not use dust covers. They were interchangeable. Does Leupold still include both sets of knobs on brand new...