Search results

Looking to trade my 0 moa Geissele for a 20 moa Badger c1 or 20 moa Geissele. Not sure if the normal (not mk5 specific) Geissele has enough space between the rings though.

Everywhere seems to be out of stock online, curious if anyone here has one they want to sell.

So, like many people these days, I'm new to reloading. The first thing I acquired was a Lee classic loader to hand load for my Remington 700p. I'm using Varget, CCI no.200 large rifle primers and Sierra 168 gr. hpbt bullets. Question is, can I use the 3.1 cc scoop that came with the loader...

I think I've decided on a Leupold MK 6 1-6x for my "do it all" optic for my AR. Problem is, I can't decide between the TMR-D and CMR-W reticles. I will shoot different loads (XM193, M855, MK262 as well as hand loads when I get the press and dies), so I'm leaning towards the TMR-D since it's not...

Who has used both of these? I think I have decided on the SAS Ti Arbiter, but can't decide on the mounting system. It will be used mostly on my 700P shooting out to 500 yards (farther when I find somewhere I can shoot 600-1000), but I also plan on using it on my 14.5" AR (5.56), and a 8" 300BLK...

I just saw this.. cheaperthandirt.com I've been looking at threaded .22 pistols to use as a host for my first suppressor when I get it, and I have narrowed it down to a few.. I keep trying to make up my mind between the GSG 1911 and a MK II/III/22/45, and this might have made my mind up...

Is there a reason for barrels mostly being 16", 18", 20" etc. rather than say..17", 19", 21"? Just curious.

So, I was putting an EGW base on my 10/22, using my friend's torque wrench set to 20 in/lbs (just like EGW said on the package) and the screws kept turning. I was careful not to cross thread them when getting them started, and tightened them very loosely with a regular allen key before using the...

For what I can spend, and the type of stock that is comfortable for the type of shooting I will be doing, I've narrowed it down to the Bell & Carlson target/varmint, and Boyd's tacticool. Being a composite stock, do you guys think the B&C has any advantage over Boyd's laminate as far as...

Anyone have one? I'm getting my first suppressor in the next 4-6 months, (if the ATF is not super slow with the paperwork) and was trying to decide between a Ruger MK II/III or a Browning Buckmark to put it on. I had it narrowed down to this.. <a...

Is that a bad idea? If not, what is a good solution as far as mounts that will fit both guns and the same suppressor? It's a 700 PSS and a 14.5 in. midlength gas WOA barrel on the AR.

How bad of an idea do you think this is? Do you think the fumes would stay in the oven even if I leave it open for a few days after to air out, and then do the self cleaning cycle? I'm having a hard time finding any other place to cure my parts after I paint them. I thought I could use the paint...

Anyone know of a tough aftermarket extractor, or is the factory replacement fine? It is stainless btw.

I noticed that my barrel is rubbing my stock towards the inside end of the stock, above where my bipod is mounted. Can I just go in with sandpaper around a pipe or dowel to take out some material on the stock myself, or is there a better way? It's a Remington PSS with the HS stock btw.

It's kind of hard to get a good picture of, but there is powder residue that blows out the front of my gas block. Is this normal? This is the first stainless barrel I've had, and I never noticed this on the parkerized guns I've shot.

I have a vx-III that I am going to change the reticle in, and am wondering if I should keep it simple and go with the mildot, or get the tmr. From what I have read, it seems the tmr is superior, but does it work with the mildot master? The math part of this long range stuff really confuses me.