Search results

I have a Colt 9mm 6951. I would like to buy some spares such as the stainless steel trigger pins, similar bolt and fcg. Anybody know who has these that isn’t a Chinesium dealer in disguise? Thanks for your help. Amanda

Stopped by my LGS to look at what they told me was a new Remmy 700 short action rifle. They had three in stock. All were look-alikes with an RAR prefix serial number. The counter guy had never heard about the Alpha models, the change to a bolt release on the action body, or any other changes. I...

One of my Radian Raptor charging handles failed last week. The left side latch hook sheared off and was only noticed when removing the bcg for cleaning. The fracture appeared to be at a porous casting area. I called Radian up, sent them a few pictures, and asked for a new left side replacement...

Called Bergara after I found out my HMR PRO .300 WM wouldn’t ignite CCI-34 NATO spec primers. Ever. Bergara service rep said they would send me a new spring, and it would work. He did, and it worked. Wolff couldn’t help, nor Brownells. The spring is longer than the original, and a bit harder to...

After changing my mind about buying a KRG, I bought an AT-X chassis from MH. Stuck my .223 Remington SPS 5-R in it, and found out the difference the chassis makes compared to the factory Hogey Samich rubber stock. Group size using 69gr Noslers went from 1.5” to <0.5” at 100 yards. The chassis is...

While doing load development with my 700 in .223 Remington, I used factory loads and my handloads. My 73gr ELD handloads using CCI 400 SR Primers worked 100%. Federal factory 55gr FMJ loads worked 100%. ALL NATO spec loads from the factory, the ones with crimped and/or sealed primers, failed to...

Howdy, I notice that the AT-X action is found in either 6 or 6.5mm only. Is it possible to get a bolt face for an AT-X factory action that will accept the 6.8SPC case head of the Valkyrie, have a barrel made up, and be able to use the .224 Valkyrie? If so, which magazine would be the best fit...

Howdy folks, I have the itch to purchase a folding chassis to replace the issued Hogue rubberized plastic stock on my 700 SPS in 5.56mm. Comparing the Cadex to the KRG, MDT Carbon Fiber and MPA folders. I am after most solid rigidity when locked open, AICS Mag capability and adjustable...

I had two “Notify Me” tickets in for two different Remington Primers for the last few months. Today, Midway emails told me that Remington Primers are discontinued. I guess I should keep the last brick of SP Remingtons that I bought locally, for collectors items😹

Check out Blue Collar Reloading in Salisbury, NC. I just snagged 10# of Retumbo and 2# of H1000. Only primers they have are LP, but they have popular brass and bullets, and are well-stocked with many flavors of powder. Prices are mostly pre-Kung 🤒 Flu. 🤡

Since before the Antifa mess started, police have been getting shot to death with increasing frequency. I have noticed that many have been shot multiple times, with some being able to obtain help and survive, while others are dead right there. Do police in general wear body armor, or do many...

I decided to load a few thousand pistol cartridges, since my rifles are waiting on some new bullets. First round the primer slide failed to pick up a primer. Ten tries later, still no primer. Took the primer slide out, caliper said it was small enough to slide freely, but it stayed stuck, even...

Seems to me, who voted a straight Republican ticket in NC a week ago, that all of the worry about who is the hmfic is misplaced. The Senate seems to be the only actual roadblock to the commies. Trump does a great job for being clueless, except he continues to surround himself with conniving...

Just asking. Coming from mainly pistol reloading, I now reload for .300 Winchester Magnum. My normal process is take my virgin brass, usually Winchester or PPU, place 50 in the loading block and inspect the case mouths. PPU, I find few, if any issues. They are ready to uniform the flash hole...

I found some 230gr A-tips at Midway, in stock. Looked the pics over, and ordered 300. They arrived today, plastered with the requirement for a 1x9 or faster twist rate. Of course, mine is 1x10. Midway makes it easy to return these, so no big deal. However, I am wondering if anyone has tried them...

SOLD: I purchased a folding AX stock for my new .300 Win Mag Bergara HMR Pro after 50 rounds were expended using this factory stock. Looks brand new, and will ship as shown with bottom metal and both action screws. You'll see the tape holding the screws into the action holes. I will include 2...

Perfect transaction. Does what he promises. Deal with confidence.

Wondering if anybody is having the problem of their seating die leaving a circular ring on the bullet’s ogive? I use a Bonanza Co-Ax, and it allows very gentle seating pressure. My Redding seater die works fine for Hornady 75gr bullets, and does not leave the ring. However, when loading the 90gr...

SOLD! I had a Swedish Mauser for a few years, gave it to my nephew, who traded it for a drone. Ugh! Anyway, I have this lonely bag of 50 Winchester virgin brass available. Price is $16 shipped. PayPal F&F, USPS Money Order or Certified Check. Thanks!

SOLD to Wheres-Waldo 8/18/20> -Compass Lake Engineering AR15 barrel. CLE chambered and set up this Krieger 1-7.7 twist 5.56mm barrel for me to use at Perry in April of 2009. I used it that year, then got bit by the Garand and M-14 bug, so it has sat unused for years. Round count is 1500, +/-...