case

Haven't able to find a lot of info for the FHF gear rifle case, just wondering if anyone have some experience with it? Planning to air traveling with my competition rifle with Pelican 1750 + either the FHF rifle case 50 or the Eberlestock drag bag 52. Saw some recommendation for the Pelican +...

For "Magnum cartriges" (300WM, 300NM, 338LM, etc). Brand new, never used. Uses a SKB 0907-6 I Series case. It has 50 holes to accommodate up to 50 rounds. MAX OAL of loaded round, 5.50" PayPal, Zelle or Venmo. $70 + $15 shipping

For 50 BMG/Barrett 419 (could really use it for other "large"calibers). Brand new, never used. It has 50 holes to accommodate up to 50 rounds. This case is designed to house 50 BMG and Barrett 419 cartridges. The cases listed will take a round with an overall length of 8.00”. $200 shipped

Upgraded phones and don’t have my old one anymore. Looking to just sell this for $20 shipped. It has the case and the piece that centers the phone camera. Just needs whatever adapter is required for your optic

I use the wheels for 6.5 Creedmoor, so they'll work for .223 up to .308 I believe. I'm switching calibers and my new, smaller case won't work in this one. I love the thing and it's so nice to load up 75+ cartridges and just let them go. Anyway, the wheels have some wear on them but it still...

In nice shape and ready to use. *Sold*

What cases do y'all use, specifically for the longer bolt guns, like full chassis 24"+ barrels? i have a Remington 700 300wm, in an AICS 2.0 stock, and I need a case for it, what are my hard and soft options?

Hopefully this can just be a fun spot to show off your gun case setup and give other people ideas on what to do with theirs... Whether you have a top of the line Pelican case, or the flimsy black case your gun came in (like me ;) ), be proud of your setup and post a picture of your case!

Hey guys Whats the BEST case trimmer ? Not the fastest, but the most accurate every time...

I hope that this is in the right section! I have a case similar to a pelican case that has 2 layers of flat foam in it. I was wondering what the ideal way to cut the foam to the shape of the rifle would be? Should I just give it a whirl with the exacto knife or what?

Hi newbie here after looking at made in China and over priced Drag Bags I have decided to make my own.I served in the us army in germany in the 80's in the first LRS unit since the Vietnam war.Not bragging but did a lot of crawling dragging and shooting.Unfortunately we didnt get to actually...

With two of the familiars merged (Hardigg/Pelican) curious about what other offerings are out there and what experiences people have had. Any others? Any standout offerings for a specific size range or category? Also, locks? Saw where SKB offers TSA compliant locking latch upgrade, any other...

I remember there was a thread dealing with the theory/ usability of this setup, but I never liked the options of soft cases that were found to be in the golden ratio of 42x13x5... Until today: I finally bit the bullet and took a chance on the I Shot SERT 42" case and have no regrets. It fits...

[updated 3/15/2013] Hello everyone! Decided to provide some video links I found online for setting up a Pelican Case. Just a few notes I took from these videos Materials needed: -Pelican Case -Black or silver Sharpie/Marker or chalk (chalk is sounds better than permanent) -Electric knife...

ordered a foster case trimmer , the one that fits on a drill press , also ordered the hollow pointing tool, thought it would be a fast way to trim, any way did a couple of cases , but you can see the cut is not square , put a 308 in with a vmax loaded and chucked a needle in the drill to line...

I would like some opinions from the folks here. I have been diagnosed with severe degenerative arthritis in my left wrist, and am pretty sure it's in my right wrist as well. I also have arthritis in my thumb joints (bilateral basal joint arthritis). Trimming brass with my Lyman trimmer, even...

I just trimmed 50 rounds of LC 5.56 and was thinking maybe I trimmed to much. I am loading for a 5.56 AR15 and read the Hornady manual and it says 1.750, is this right for 5.56?

Got the chance to get out and burn some powder today. Shot several hundred rounds through my DPMS LR308. All was fine till this one was fired. Got peppered with hot gas and shrapnel (no damage to me). The follower in the mag was blown down and lodged sideways in the mag body and the floorplate...

I know these are just hitting the market, but I welcome comments from anyone who's seen this thing work (or who has one). http://accurateshooter.wordpress.com/200...ter-hit-market/

I picked up one can each, first time they have been avail for months here, I know I should try them both first but any yea or nay about either of these before breaking the seal? At this time, these are the only two spray lubes I can find in my AO and I would like to stock up while they are avail...