cases

Click on products.. some really cool stuff here.. http://www.technoframes.com/

what do i do to clean cases without a tumbler?what do i use specifically please

How much denting in the case should be allowed before tossing in the trash? I understand that dents in the main part of the case will usually flatten back out upon next firing, and the die straightens out the case neck sufficiently.

Just bought an AR-15 from a guy who put it together himself...I know, I know...probably not smart, but I did it. I chamber a round, fire, the bolt opens and tears the rim on the case but the case won't come out. Removed case, cleaned chamber and tried it again. Same result. Any ideas? I...

I searched. Too many hits that don't have all three search terms. Anyway, my FA63 match holds 55-56 grains of H2O, depending on how high I run the meniscus. Or was that the difference between sized and fired? So many facts, so few remaining brain cells. IIRC, Lapua holds 56 or whatever. Just...

O.K., getting my FN/SPR slowly together. Just ordered my rings, bolt handle is back from G.A., suppressor should be clearing soon. Now it's time for a case. I was going to go with something like a Pelican or Storm, but what about the soft cases? Say like something from Eagle that will also...

i HAVE SEVERAL HUNDRED MILITARY CASINGS THAT NEED DEPRIMED AND LOADED WITH CIVILIAN .223 PRIMERS. i HAVE BEEN TOLD THAT i MUST USE A SPECIAL TOOL TO REMOVE THE OLD PRIMER AND TO PREPARE THE FLASH HOLE FOR CIVILIAN PRIMERS. i NOTICED THAT SOMEWHOW i ACCIDENTALLY SLIPPED A FEW MILITARY CASINGS IN...

Can a case be too short? I was trimming necks on a bunch of brass I inherited. I was following the guidelines for a trim to length of 1.902". I found a couple cases that were as short as 1.895". All appeared at least 1x fired. I don't have an unfired piece of new brass to compare to so I dont...

http://bouncewith.me.uk/europe/8027043.htm

hello all, i was wondering if anyone knew where or how to get the foam cut to fit your rifle for a storm or pelican case?

I'm on the list to get a Giraud but it is looking like up to 6 weeks for shipment. I was wondering if you could get good results using a quality drill press...does anybody use a press with the Forster Power Case Trimmer? Do you get good results? Thanks!

Does anyone know about how many cases you can fit into a .50 cal ammo can. I really don't want to have to count them.. I'm thinking like.. 700?? Thanks..

A few of my friends were saying it's worthless... the Lake City stuff looks good to me, any issues?

Well, I started prepping my new brass today. My last batch of lapua did not have a single bad case in the lot. I open the first box today, and I had 10 out of 100 cases that had their necks smashed flat. I was surprised, I'm used to this with remington cases, but not lapua. I hope my other...

Does weighing cases help any? How about checking the volume of the cases? Tring to get max accuracy for an upcoming match, looking for any advantage, but if this doesn't improve things much I don't want to waste my time. Please only respond if you have done this and know first hand.

I am looking for a nice rifle case for my AICS bolt rifles. I have thought about a storm case but i would like to know whats out there in a nice sturdy soft case. Tactical type!! Thanks Lee

This is my first attempt at pistol reloading so I have no doubt it's something stupid. I am reloading .45 ACP on a Dillon 550 using RCBS dies that a buddy let me borrow because I couldn't find any dies. I resize the case, and it fit the cyclinder of my S&W 625. I then move them to...

Just want to know if there is any potential problems with doing this...? A buddy and I shot some 6x47 Swiss Match through my 6x47L yesterday, and got a 1 inch drop in POI at 600yds vs the Lapua brass we were shooting... Don't even know load info, velocities or anything at this time... just...