screws

I am looking at two different mounts for my aimpoint t2. One is the larue and the other is ADM. I like the ADM more but it looks like they come with YFS screws which I have heard are bad any truth to that?

What action screws are you guys using with your Manners MCS? (700 SPS) Received my T4A stock from Manners with no action screws... I couldn't get my old action screws to work. Possibly they need to be trimmed? or maybe they require a whole different set up all together? I do know it's a 1/4x28...

Does anyone know what size Torx screws come with the Badger Ordnance 20 MOA savage short action base? The item code is 306-06SAT and everywhere I look at best just mentions that there are Torx screws included. I lost the screws (D'oh) and now I have to order more. I see 2 different sizes on...

I recently realized that the set screws for my scope turrets are rounding because of crappy Allen keys. I'm worried that if I replace them, they'll probably just round again, since they only use a 1.5mm hex key. So what I'm thinking of is buying some new set screws and then slotting the head...

Having spent more on my scope than I have on my rifle I want to make sure I don't screw anything up. The IOR paperwork that came with my scope specifies 12 in/lb max when tightening the scope ring screws. Two novice questions... 1) I've looked for a torque hex head screwdriver, but can't...

Anyone know the proper size hex wrench to use on the action screws in an AICS? It appears that I don't have the proper size wrench. It's always something.

I won an auction on GunBroker for a set of (3) screws for a Remington Model 700 ADL. I sent payment and received only 2 screws. Only thing is I can't for certain verify that they even go to my gun because I haven't acquired the action yet. With that said an ADL model is just that right? I was...

McMaster Carr PN 91290A136. Pack of 25 screws for $5.81.

i watched the movie shooter again last night and noticed something i havent seen before, in the opening sequence when walberg is on top of the ridge with his spotter i noticed that on the non ejection side of his reciever where on some rifles there is a side bolt release on his rifle there is 2...

Seems like I saw a post on this a while back but searched it and could not find it. I am installing an EGW base on a buddies REM 700 and the supplied screws are to small in diameter. Anyone know what the size is for the REM 700 receiver?

I aquired a Seekins 20moa base and 30mm rings(lightly used) today and the base did not have the 4 screws with it. Where can I find the four screws I need? They would be the standard 6x? (Rem 700) Please advise. Mark

Gents, I need a set screw for a G 21 compensator. The comp screws on to the barrel but is held in place with a set screw that must go low enough into the hole to allow the operating rod into the bottom of the comp. Size is 5mm diameter and 4mm or less in length. Any help is deeply...

Well, i also just realized that I don't ahve a torque wrench that goes down to 20 in/lbs, lowest I have is 25 in/lbs. So, how critical is it that I use a torque wrench for the base. I obviously don't want to overtorque, but I don't want to undertorque it either, and what about the rings...

who sells torx action screws? i can only find allen head and would prefer torx for a build. and does material matter when getting a recoil lug (steel/ss)? fyi action is steel and barrell is stainless.

I really may be screwed but I thought I'd throw this out for some ideas. I thought I saw this come up a year or so ago, but couldn't find it in the search, or was using the wrong keywords. Problem, I have a 700 in .223 I bought, had barreled and set it in a McM stock I had laying around...

Does anyone know the size of these screws. I have a sako optilock base and (3) 30mm rings for my trg and the heads of these screws are so soft they couldnt take 15 in lbs of torque before I stripped 2 of them. I would like to find replacement screws for my rings preferably torx heads, any idea...

Finally mounting up the Ken Farrell 20MOA base and putting the Falcon Menace on my Savage 110. I found lots of good advice here via the search and FAQ on leveling and everything, but I can't find any info on how to fix my issue, which is this: When I torque the base mount screws, they bind the...

I bought a gun over the net, and when i tried to take off the bases, it looked as if they were glued on. (all around both front and real looked like to be a Carmel color coating) Finally got he bases off but the receiver is still covers in this stuff as well as the bases and screws. I soaked...

Where can find a set of new action screws for my AICS? A defective torque wrench has led to stripped screws( D'oh!!!!!!)

Can anyone tell me the screw sizes for the Badger Ord rings? Had a set given to me; however two of the screwheads are buggered up. I think they are 8-40's but I don't know the length. Any help would be appreciated.