specs

Does anyone know where I could find good specifications for the different ACOG Reticles? Dot, Chevron, Duplex, Triangle heights, widths, thicknesses? Bullet Drop Compensating Reticle Mil or MOA dimensions? The web site info is very shitty.. is this too much to ask for just and ACOG? I know it's...

What specs do I need to look for in a spotting scope that will be used for shooting out to a 1000 yds? Any recommendations that you have for a particular model are welcomed. I keep reading good things about the new Bushnell with the mil-dot reticle. I am looking for the best bang for the...

Does anyone know what the torque specs are for the Tikka T3 action screws? I have this fear of cracking the factory floorplate.

Does anyone have one of those nifty illustrations of the SAAMI specs for the 6.5x47 Lapua. I think I have a shoulder issue, I am getting a stiff bolt close, and the bolt is "pop" when I lift the bolt, just past the begining of the cam. I am using Forster Dies, and have it screwed all the way...

My Google-fu has let me down. Does anyone have the specs for Armalite's AR10 SASS barrel? I am looking for length, twist rate and profile specs? I plan on ordering a Bartlien AR10 blank and want to have it profile correctly.

I was wondering if anyone knows what the M118lr cam for the NF F1 scope is calibrated for... I know it is for the 175 smk's... But does anyone know what Velocity? Im asking because id be using a 24" barrel...

how much torque should I use on.. nightforce picitinny rail on savage action and the action screws on the HS Precision stock. I suspect that the actions screws would be the same on all hs stocks..65IN/LB??

now that i have a wheeler torque driver i need to know how many inch pounds do i tighten the action screws/aluminum rings to steel base and scope ring srews?

If anyone has upgraded their 77/22 and wouldn't mind sharing some pics and specs I would appreciate it. Starting point is Ruger's 77/22 all weather, the one with the tapered heavy barrey brushed stainless finish. Thanks dgwelsh

I need to get a factory spec sheet on the 700 action. I am particularly interested in the OD dia / Rad both front and rear since they are different from each other. Thanks.

Good Day Everyone, First let me apologize for a "VS" thread As I not really wanting to debate which is better but rather am wanting to discuss ballistic data for the sake of knowledge. Recently I had a work specific .308 built that sorta deviated from the norm of things in regards to the...

i am guilty of being a tight a$$ and was pondering a new bench gun. i was really wanting a 30br but with the price of brass and the availability i started looking elsewhere. i also have a full length 308 tactical rifle in the works. anyway, i thought i might just buy a match 308 reamer and run...

Hey guys,I am looking for either good specs or pics for the cuts to fit a spec M40A3 picatinny rail.Thanks in advance. Wombat

Hi does anyone have the chamber diagram for Remingtons new 30AR? i have heard it is a shortened 284 case but the performance seems poor a 125gr projectile at 2250fps a 30BR will do that but i am wondering how it would go necked to 6mm so if anyone has a fired case or reamer print and the case...

I recently had to remove my McMillan stock from my 40X receiver. I spilled some bore cleaner on the action and it ran underneath.....I was worried it would eat up the bedding. Anyways, can anyone tell me the torque specs for the three bolts? Starting from the big one that goes through the...

I know the info is in here buried, but rather than sifting through it figured I'd toss up a quick post for the savvy smith.... I need two barrels, Bartlein is my company of choice since I've had such good results with my current tube from them. I know the wait times are long but these tubes are...

will someone with a caliper and a hs stock measure the forend for me and post the approximate width? Thinking about building up a ADL stock to beaver tail forend and that is the approximate size I want.

Tryed a search for about 15 minutes and coulnt find much. Could someone either post a link or answer the following for the proper torque specs... Action Screws Base Screws Ring Screws Ring Cap Screws Any other tourqe specs I can add to the list?

7mmRM is working to aquire these for me but, if anyone has a drawing and or the specs for the M40A3 Clip Slot Cut Out I would appreciate it if you would share them with me. I'm trying to help/finish up a rifle for a fellow Hide Member and thats the only metal work left prior to refinishing...