- Thread starter Two Shoes
- Start date
Re: Loads for 7 Rem Mag
Factory Remington Sendero at 26"
Berger 168VLD
Win Brass
215M primer
65.0 gr. of Reloader 22
COAL 3.426 (touching lands)
Consistent .3 load.
Factory Remington Sendero at 26"
Berger 168VLD
Win Brass
215M primer
65.0 gr. of Reloader 22
COAL 3.426 (touching lands)
Consistent .3 load.
Re: Loads for 7 Rem Mag
Berger 168 VLD jammed into the lands
Win Brass
Fed215M
71.5 grns of Retumbo
3100FPS via 28" tube
Berger 168 VLD jammed into the lands
Win Brass
Fed215M
64.5 grns of RL19
3050FPS via 28" tube
180 Berger VLD
Win Brass
Fed215M
63grns of RL22
2975FPS via 28" tube
Berger 168 VLD jammed into the lands
Win Brass
Fed215M
71.5 grns of Retumbo
3100FPS via 28" tube
Berger 168 VLD jammed into the lands
Win Brass
Fed215M
64.5 grns of RL19
3050FPS via 28" tube
180 Berger VLD
Win Brass
Fed215M
63grns of RL22
2975FPS via 28" tube
G
Guest
Guest
Re: Loads for 7 Rem Mag
These two loads have the same 100 yard zero within 1/4" of each other .
PSS 7mm rem mag 26" 1/9 and 1.16 twist
ww brass
162 AMAX
67gr RL22
215 primer
seated to kiss the lands
1/4 moa capable..
nail driver in low and hi temps
3050
------------------------------------
pss 7mm rem mag 26"
ww brass
180vld burger
63gr RL22
215 primer
2850-2900 fps
seated as deep as i can get it in the lands without preasure sign.
These two loads have the same 100 yard zero within 1/4" of each other .
PSS 7mm rem mag 26" 1/9 and 1.16 twist
ww brass
162 AMAX
67gr RL22
215 primer
seated to kiss the lands
1/4 moa capable..
nail driver in low and hi temps
3050
------------------------------------
pss 7mm rem mag 26"
ww brass
180vld burger
63gr RL22
215 primer
2850-2900 fps
seated as deep as i can get it in the lands without preasure sign.
Re: Loads for 7 Rem Mag (from Jeffbird)
<span style="font-weight: bold">(from Jeffbird) </span>
<span style="font-weight: bold">FOR 7WSM</span>
24" 1:9 Broughton by Chris Matthews, Long Shot Rifles
All with F210M & sized with Forster BR dies
150 Barnes TSX 67.0 MagPro 3100 - Hunting load
162 Amax 64.4 RL22 3060
176 Cauterucio 66.5 MagPro 2900 23.5 MOA to 1,000 yds.
176 Cauterucio 61.1 RL22 2815 25.50 MOA to 1,000 yds.
The MagPro is cooler and slower to heat the barrel than RL22 for comparable round counts under same conditions.
All loads were worked up at 1,000 ASL during the summer with temps up to 100F in Texas.
7 WSM load thread
<span style="font-weight: bold">(from Jeffbird) </span>
<span style="font-weight: bold">FOR 7WSM</span>
24" 1:9 Broughton by Chris Matthews, Long Shot Rifles
All with F210M & sized with Forster BR dies
150 Barnes TSX 67.0 MagPro 3100 - Hunting load
162 Amax 64.4 RL22 3060
176 Cauterucio 66.5 MagPro 2900 23.5 MOA to 1,000 yds.
176 Cauterucio 61.1 RL22 2815 25.50 MOA to 1,000 yds.
The MagPro is cooler and slower to heat the barrel than RL22 for comparable round counts under same conditions.
All loads were worked up at 1,000 ASL during the summer with temps up to 100F in Texas.
7 WSM load thread
Re: Loads for 7 Rem Mag (from Jeffbird)
Does anyone load 7mm Rem Mag w/ 175 SMK and 4831? I have a couple of loading manuals they both say the max load with that bullet weight and that powder gives around 2660 fps. I have loaded to this point and have decent accuracy. However, I have also read other places and heard from knowledgable people that they will load this same bullet and powder up to 2950 fps. What is up with that? Do the loading manuals tend to be overly conservative for legality sake? This is what I tend to think. I guess I'll have to keep on loading and see what I can do without over pressure.
Does anyone load 7mm Rem Mag w/ 175 SMK and 4831? I have a couple of loading manuals they both say the max load with that bullet weight and that powder gives around 2660 fps. I have loaded to this point and have decent accuracy. However, I have also read other places and heard from knowledgable people that they will load this same bullet and powder up to 2950 fps. What is up with that? Do the loading manuals tend to be overly conservative for legality sake? This is what I tend to think. I guess I'll have to keep on loading and see what I can do without over pressure.
Re: Loads for 7 Rem Mag (from Jeffbird)
Lucky7mm,
Skip the 4831. Get some RL25, RL22, RL19, Retumbo- You will easily get to that velocity and have great accuracy.
Lucky7mm,
Skip the 4831. Get some RL25, RL22, RL19, Retumbo- You will easily get to that velocity and have great accuracy.
Re: Loads for 7 Rem Mag
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Lucky7mm</div><div class="ubbcode-body">Does anyone load 7mm Rem Mag w/ 175 SMK and 4831? I have a couple of loading manuals they both say the max load with that bullet weight and that powder gives around 2660 fps. I have loaded to this point and have decent accuracy. However, I have also read other places and heard from knowledgable people that they will load this same bullet and powder up to 2950 fps. What is up with that? Do the loading manuals tend to be overly conservative for legality sake? This is what I tend to think. I guess I'll have to keep on loading and see what I can do without over pressure. </div></div>
<span style="font-weight: bold">60.9 get's you 2900, from a Sierra manual, for std 4831, what are you looking at?</span>
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Lucky7mm</div><div class="ubbcode-body">Does anyone load 7mm Rem Mag w/ 175 SMK and 4831? I have a couple of loading manuals they both say the max load with that bullet weight and that powder gives around 2660 fps. I have loaded to this point and have decent accuracy. However, I have also read other places and heard from knowledgable people that they will load this same bullet and powder up to 2950 fps. What is up with that? Do the loading manuals tend to be overly conservative for legality sake? This is what I tend to think. I guess I'll have to keep on loading and see what I can do without over pressure. </div></div>
<span style="font-weight: bold">60.9 get's you 2900, from a Sierra manual, for std 4831, what are you looking at?</span>
Re: Loads for 7 Rem Mag
4831sc, and the std IMR 4831, run fine speeds.........what velocity are you after?.3,000+?
4831sc, and the std IMR 4831, run fine speeds.........what velocity are you after?.3,000+?
Re: Loads for 7 Rem Mag
I've got H-4831SC actually. Looking at data from Hodgdon and Lee. Perhaps Lee got their data from Hodgdon. Even if I can push it to 2850, that's still a good deal faster than I'm going now. I'll just have to try it and watch out for pressure. I'm still kinda new to reloading, having done it for about 3 years. Don't know exactly what all the pressure signs look like yet. I know to look at the primers for being flattened as well marks from the bolt face (ejector, extractor). Any bulges or failures of the case are a no brainer obviously.
Maybe I should mention that this is a Rem 700.
I've got H-4831SC actually. Looking at data from Hodgdon and Lee. Perhaps Lee got their data from Hodgdon. Even if I can push it to 2850, that's still a good deal faster than I'm going now. I'll just have to try it and watch out for pressure. I'm still kinda new to reloading, having done it for about 3 years. Don't know exactly what all the pressure signs look like yet. I know to look at the primers for being flattened as well marks from the bolt face (ejector, extractor). Any bulges or failures of the case are a no brainer obviously.
Maybe I should mention that this is a Rem 700.
Re: Loads for 7 Rem Mag
Jeff, it say's 7WSM Thread at the bottom, but I put it at the top also.
Jeff, it say's 7WSM Thread at the bottom, but I put it at the top also.
Re: Loads for 7 Rem Mag
7WSM
175 smk; 65.0 RL25; Fed 215M primers; Win brass; OAL 2.86"; 2,900fps 26" Kreiger 9 twist.
175 smk; 66.4 H1000; Fed 215M primers; Win Brass; OAL 2.86", 2,875 26" Kreiger 9 twist.
JeffVN
7WSM
175 smk; 65.0 RL25; Fed 215M primers; Win brass; OAL 2.86"; 2,900fps 26" Kreiger 9 twist.
175 smk; 66.4 H1000; Fed 215M primers; Win Brass; OAL 2.86", 2,875 26" Kreiger 9 twist.
JeffVN
Re: Loads for 7 Rem Mag
has anyone tried 180 bergers 7wsm probley have to single feed i would think .
has anyone tried 180 bergers 7wsm probley have to single feed i would think .
Re: Loads for 7 Rem Mag
How about the 160gr. Nosler Accubonds for hunting with some RE-22, anyone have any good data that worked for them? It will be used in a factory Rem. 700 CDL in 7mm Rem Mag.
Thanks,
Chance
How about the 160gr. Nosler Accubonds for hunting with some RE-22, anyone have any good data that worked for them? It will be used in a factory Rem. 700 CDL in 7mm Rem Mag.
Thanks,
Chance
Re: Loads for 7 Rem Mag
I am debating between a 6.5 284 and a 7mm Rem Mag. Ballistically, the 7mm has got my eye, but I have been warned about the recoil. How do these loads feel. I will be firing about 50 rounds per competition.
Thanks
I am debating between a 6.5 284 and a 7mm Rem Mag. Ballistically, the 7mm has got my eye, but I have been warned about the recoil. How do these loads feel. I will be firing about 50 rounds per competition.
Thanks
Re: Loads for 7 Rem Mag
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Tfears</div><div class="ubbcode-body">I am debating between a 6.5 284 and a 7mm Rem Mag. Ballistically, the 7mm has got my eye, but I have been warned about the recoil. How do these loads feel. I will be firing about 50 rounds per competition.
Thanks </div></div>
Both of my 7mmRMs weigh 17ish pounds- recoil is nill.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Tfears</div><div class="ubbcode-body">I am debating between a 6.5 284 and a 7mm Rem Mag. Ballistically, the 7mm has got my eye, but I have been warned about the recoil. How do these loads feel. I will be firing about 50 rounds per competition.
Thanks </div></div>
Both of my 7mmRMs weigh 17ish pounds- recoil is nill.
Re: Loads for 7 Rem Mag
Remington 700P 7mm remmy mag
66.5 gr RL22
150gr TSX, Nosler BT's, Swift Scirocco's (best accuracy), and SMK's. note all bullets shot under .5 moa at 100 yards and did well at 1,000 yards also
Fed 215 primers
Winchester Brass
seated out to the lands
Remington 700P 7mm remmy mag
66.5 gr RL22
150gr TSX, Nosler BT's, Swift Scirocco's (best accuracy), and SMK's. note all bullets shot under .5 moa at 100 yards and did well at 1,000 yards also
Fed 215 primers
Winchester Brass
seated out to the lands
Re: Loads for 7 Rem Mag
Got a new Sendero 7mm Rem Mag just broke barrel in with first forty loads.
Got 175 gamekings to group one inch with Magpro 66 grains.
Do you guys have some start loads for the 168 Bergers pushed to the lands. The data in the hodg. flyer is vague.
168gr Bergers
R-P Brass
wlrm
Retumbo Powder ???64?? 68??71??
Any help from some veteran reloaders, very much appreciated.
Got a new Sendero 7mm Rem Mag just broke barrel in with first forty loads.
Got 175 gamekings to group one inch with Magpro 66 grains.
Do you guys have some start loads for the 168 Bergers pushed to the lands. The data in the hodg. flyer is vague.
168gr Bergers
R-P Brass
wlrm
Retumbo Powder ???64?? 68??71??
Any help from some veteran reloaders, very much appreciated.
Re: Loads for 7 Rem Mag
7mmMag Ruger #1 box stock:
65 gr 4831sc, 175 gr Hornady spire point moly, 3.34" OAL
Shoots moa with a 6X scope and 3,000 fps.
7mmMag Ruger #1 box stock:
65 gr 4831sc, 175 gr Hornady spire point moly, 3.34" OAL
Shoots moa with a 6X scope and 3,000 fps.
Re: Loads for 7 Rem Mag
No 7-08 loads??
No 7-08 loads??
Re: Loads for 7 Rem Mag
7mm 08:
168gr SMK touching the lands
Fed Match Brass(yeah I know but I have a ton of it)
41gr H380
CCI 200 primer
7mm 08:
168gr SMK touching the lands
Fed Match Brass(yeah I know but I have a ton of it)
41gr H380
CCI 200 primer
Re: Loads for 7 Rem Mag
Taco101
What kind of velocities are you getting with the above load. At what temp? Gettign ready to do a build of a 7-08 and looking for things to try. Brock
Taco101
What kind of velocities are you getting with the above load. At what temp? Gettign ready to do a build of a 7-08 and looking for things to try. Brock
Re: Loads for 7 Rem Mag
About 2500 at 70.
I just bought a box of Hornady 162gr AMAX bullets. They were recommended on another thread on this site. Much better BC and initial velocity......I'll know this weekend, if the weather cooperates.
About 2500 at 70.
I just bought a box of Hornady 162gr AMAX bullets. They were recommended on another thread on this site. Much better BC and initial velocity......I'll know this weekend, if the weather cooperates.
Re: Loads for 7 Rem Mag
I have been looking at the 168 VLD's to shoot in my build. Even better BC than the amax's. Let us know what your results are. Brock
I have been looking at the 168 VLD's to shoot in my build. Even better BC than the amax's. Let us know what your results are. Brock
Re: Loads for 7 Rem Mag
Roger that.
Roger that.
Re: Loads for 7 Rem Mag
7mm-08
Brass: Winchester
Primer: Federal GM210M
Bullet: 162 Amax
Powder: 43.3 Gr. Vihtavuori N550
COAL: 3.001
Velocity: 2800
Barrel: 29 inch Krieger
7mm-08
Brass: Winchester
Primer: Federal GM210M
Bullet: 162 Amax
Powder: 43.3 Gr. Vihtavuori N550
COAL: 3.001
Velocity: 2800
Barrel: 29 inch Krieger
Re: Loads for 7 Rem Mag-7 WSM-7-08
For 7mm08:
Note that this is WAY (about 7%) above any published maximums that I've found. Note also that my oal is significantly longer than SAAMI specs suggest.
bullet: 162 grain Hornady Amax
powder: 42.0 grains of Varget
OAL: 2.905"
primer: BR2
brass: Winchester
barrel: 25" Pac-Nor SS Match with 8" twist
action: Savage 10
MV: 2805 fps average (was 2725 when the barrel was new and clean, it may be lower now that I cleaned it and removed the carbon boulder. In any case, MV's were always very consistent in each session)
neck tension: No idea, but I use a full-length redding bushing die, and it resizes a minimal amount. So I guess my answer would be 'not much.'
Enjoy,
Bob
For 7mm08:
Note that this is WAY (about 7%) above any published maximums that I've found. Note also that my oal is significantly longer than SAAMI specs suggest.
bullet: 162 grain Hornady Amax
powder: 42.0 grains of Varget
OAL: 2.905"
primer: BR2
brass: Winchester
barrel: 25" Pac-Nor SS Match with 8" twist
action: Savage 10
MV: 2805 fps average (was 2725 when the barrel was new and clean, it may be lower now that I cleaned it and removed the carbon boulder. In any case, MV's were always very consistent in each session)
neck tension: No idea, but I use a full-length redding bushing die, and it resizes a minimal amount. So I guess my answer would be 'not much.'
Enjoy,
Bob
Re: Loads for 7 Rem Mag-7 WSM-7-08
Thanks guys, I'm looking for a good offhand to 500m load with the Seirra 168. I gotta load mag length in a SA 700, so as much as I like Amax's they're out for my purposes.
A benchrester and another silhouette shooter told me to load around 2300fps, and as this would be slow for 600-1000yd does it sound ugly for an offhand load?
Thanks guys, I'm looking for a good offhand to 500m load with the Seirra 168. I gotta load mag length in a SA 700, so as much as I like Amax's they're out for my purposes.
A benchrester and another silhouette shooter told me to load around 2300fps, and as this would be slow for 600-1000yd does it sound ugly for an offhand load?
Re: Loads for 7 Rem Mag-7 WSM-7-08
I load about 2500 (168SMK) for rams. Any lower than that and I am leaving ringers.
I load about 2500 (168SMK) for rams. Any lower than that and I am leaving ringers.
Re: Loads for 7 Rem Mag-7 WSM-7-08
7mm08
bullet: 162 grain Hornady Amax
powder: 44.0 grains of H380
OAL: 2.800"
primer: CCI 200
brass: Federal .308 Match brass resized
barrel: Savage 22" 1 in 9
action: Savage 10
MV: 2850 fps average
30fps max deviation
Temp 55
Baro 30.09
RH 11%
wind from 11:30 at 15
It was a bit breezy this morning but it still grouped at .72" for 5. (one was very probably me.)
7mm08
bullet: 162 grain Hornady Amax
powder: 44.0 grains of H380
OAL: 2.800"
primer: CCI 200
brass: Federal .308 Match brass resized
barrel: Savage 22" 1 in 9
action: Savage 10
MV: 2850 fps average
30fps max deviation
Temp 55
Baro 30.09
RH 11%
wind from 11:30 at 15
It was a bit breezy this morning but it still grouped at .72" for 5. (one was very probably me.)
Re: Loads for 7 Rem Mag-7 WSM-7-08
7-08 w/175 smk's????
George
7-08 w/175 smk's????
George
Re: Loads for 7 Rem Mag-7 WSM-7-08
Taco
Glad to see the 162 A max is working and getting good Vol. at your 2.800" OAl. The H380 is one of the powders I am going to try. I also want to try H414, and R19. Brock
Taco
Glad to see the 162 A max is working and getting good Vol. at your 2.800" OAl. The H380 is one of the powders I am going to try. I also want to try H414, and R19. Brock
Re: Loads for 7 Rem Mag-7 WSM-7-08
For 7mm Remington Magnum...
You can reach top performance, low velocity spread with 160gr SBT / 168gr HPBT / 175gr SPT weight bullets with Norma MRP and Hodgon H1000. In a 26ic match tube speed go from 3050 fps to 3200fps in my rifle.
There is an excellent article about 7mm Remington Magnum in the 17th edition of "Hanloader's Digest". It will be a very good thing for some people to read it.... the author drive a Nosler 162gr SB at 3160fps and 3088fps from a 175gr Speer from a 24ic barrel with heavy load of H1000.
They'll understand why the 7mm Remington Magnum show some astonishing performances with only few powder... The 7mm RM is a finicky caliber to reload but when you combine right brass, right powder, right primer it's magic...
don't under estimate the of Brass... lot of 7mm RM brass have lower capacity than they should have... Favour quality brass even if the cost is price... Norma Brass have no contender... Lapua, Hornady are right choices too.
For 7mm Remington Magnum...
You can reach top performance, low velocity spread with 160gr SBT / 168gr HPBT / 175gr SPT weight bullets with Norma MRP and Hodgon H1000. In a 26ic match tube speed go from 3050 fps to 3200fps in my rifle.
There is an excellent article about 7mm Remington Magnum in the 17th edition of "Hanloader's Digest". It will be a very good thing for some people to read it.... the author drive a Nosler 162gr SB at 3160fps and 3088fps from a 175gr Speer from a 24ic barrel with heavy load of H1000.
They'll understand why the 7mm Remington Magnum show some astonishing performances with only few powder... The 7mm RM is a finicky caliber to reload but when you combine right brass, right powder, right primer it's magic...
don't under estimate the of Brass... lot of 7mm RM brass have lower capacity than they should have... Favour quality brass even if the cost is price... Norma Brass have no contender... Lapua, Hornady are right choices too.
Re: Loads for 7 Rem Mag-7 WSM-7-08
7mm-08 Hunting Load: (work up to this load, this is NOT a starting load)
R-P fireformed brass
WLR primers
120g TSX (seated at lands, moly coated)
45.5g Reloader 15
This yeilds me 3,050fps with 3/4MOA accuracy from a factory Remmy LVSF 7mm-08 in a Ti stock ...
7mm-08 Hunting Load: (work up to this load, this is NOT a starting load)
R-P fireformed brass
WLR primers
120g TSX (seated at lands, moly coated)
45.5g Reloader 15
This yeilds me 3,050fps with 3/4MOA accuracy from a factory Remmy LVSF 7mm-08 in a Ti stock ...
Re: Loads for 7 Rem Mag-7 WSM-7-08
I have no load data but someone asked me to do a drawing of a 7wsm recently. Here's what I did. Hope ya enjoy it.
I have no load data but someone asked me to do a drawing of a 7wsm recently. Here's what I did. Hope ya enjoy it.
Re: Loads for 7 Rem Mag-7 WSM-7-08
Anyone have 7-08 laods with IMR4895, specifically 130/150SMK's??
Nice website Robert!!
Anyone have 7-08 laods with IMR4895, specifically 130/150SMK's??
Nice website Robert!!
Re: Loads for 7 Rem Mag-7 WSM-7-08
7mm WSM
35*F
7500 Feet
180 Berger
COAL 2.965
24" Broughton
63g H4831 2940FPS
63g RL22 3027FPS
67g H1000 3011FPS
All loads were a little hot, not really to bad though. It was freezing and altitude is high. Im going to dial down a couple grains and see how velocity holds up. H1000 and RL22 seem to hold better groups.
7mm WSM
35*F
7500 Feet
180 Berger
COAL 2.965
24" Broughton
63g H4831 2940FPS
63g RL22 3027FPS
67g H1000 3011FPS
All loads were a little hot, not really to bad though. It was freezing and altitude is high. Im going to dial down a couple grains and see how velocity holds up. H1000 and RL22 seem to hold better groups.
Re: Loads for 7 Rem Mag-7 WSM-7-08
Anybody know who else makes 7mm WSM brass besides Winchester?
You guys realize that even though SAAMI says the case length is 2.100", it's only about 2.090. And it hasn't reach 2.1" even after 6 reloads and without any trimming. What's up with that?
Anybody know who else makes 7mm WSM brass besides Winchester?
You guys realize that even though SAAMI says the case length is 2.100", it's only about 2.090. And it hasn't reach 2.1" even after 6 reloads and without any trimming. What's up with that?
Re: Loads for 7 Rem Mag-7 WSM-7-08
7mm WSM
162 A-max--64grn H4831sc, WLRM Primer, Win Brass, 2.291 base to ogive, 2970 fps, sub 1/2 MOA @ 100
175 SMK--62.5 grn H4831SC, WLRM Primer, Win Brass, 2.310" base to ogive, 2850 fps, .75" @300 yards 5 shots.
180 VLD-- 67 grain H1000, Fed match primer, Win Brass, 2.278" base to ogive, 2900 fps, 1/4" at 100 yards
7mm WSM
162 A-max--64grn H4831sc, WLRM Primer, Win Brass, 2.291 base to ogive, 2970 fps, sub 1/2 MOA @ 100
175 SMK--62.5 grn H4831SC, WLRM Primer, Win Brass, 2.310" base to ogive, 2850 fps, .75" @300 yards 5 shots.
180 VLD-- 67 grain H1000, Fed match primer, Win Brass, 2.278" base to ogive, 2900 fps, 1/4" at 100 yards
Re: Loads for 7 Rem Mag-7 WSM-7-08
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Paoers</div><div class="ubbcode-body">Anybody know who else makes <span style="font-weight: bold">7mm WSM brass besides Winchester? </span>
You guys realize that even though SAAMI says the case length is 2.100", it's only about 2.090. And it hasn't reach 2.1" even after 6 reloads and without any trimming. What's up with that? </div></div>
<span style="font-weight: bold">
NO ONE............................</span>
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Paoers</div><div class="ubbcode-body">Anybody know who else makes <span style="font-weight: bold">7mm WSM brass besides Winchester? </span>
You guys realize that even though SAAMI says the case length is 2.100", it's only about 2.090. And it hasn't reach 2.1" even after 6 reloads and without any trimming. What's up with that? </div></div>
<span style="font-weight: bold">
NO ONE............................</span>
Re: Loads for 7 Rem Mag-7 WSM-7-08
Paoers Ive noticed the same with my brass. Still 2.090 after 2 reloads.
*********
My 180 berger loads were smokin hot, dialed em down a little. here is what I came up with.
7mm WSM
35*F
7500 Feet
COAL 2.965
24" Broughton
59g H4831 2808FPS (only 3 FPS deviation among 4 shots!)
59g RL22 2828FPS
62g H1000 2785FPS
The 4831 and the RL22 were still way hot. H1000 looked great, could use a little more, gonna try 63g and 63.5g. H1000 shoots the tightest also.
Paoers Ive noticed the same with my brass. Still 2.090 after 2 reloads.
*********
My 180 berger loads were smokin hot, dialed em down a little. here is what I came up with.
7mm WSM
35*F
7500 Feet
COAL 2.965
24" Broughton
59g H4831 2808FPS (only 3 FPS deviation among 4 shots!)
59g RL22 2828FPS
62g H1000 2785FPS
The 4831 and the RL22 were still way hot. H1000 looked great, could use a little more, gonna try 63g and 63.5g. H1000 shoots the tightest also.
