BLUF: Lots of parts and backstory, $5100 shipped
I’ve had this for about 2 years and I initially got it as a Gen 1 Titan chambered in .40 without an optic cut. I sent it out to DSC gunworks to get the following done:
-Recoat entire gun
-Bronze 9mm barrel
-Cut for Atlas optic plates
-Trigger job
-Cut for flashlight rail (if you have a good eye you’ll notice that the recoil lug slot isn’t as far back as it should be and you’d be right, the manufacturer info is on the bottom and he cut it as far back as possible without disrupting that. You can still run a X300-B if you remove the lug and just clamp it on the sides super tight. Lame, I know imagine my discontent when it was done without knowing that upfront)
Since then it’s got at least 4,000 rounds on it if I had to guess. None of the wear you see is from being negligent, I just used this gun a lot in dry fire and to be a USPSA gamer.
Includes:
-Gun
-Holosun 507Comp
-5x 23rd (as configured) 9mm mags 140mm
-3x 140mm MBX mags for .40cal
-3x various holsters, 2 have QLS forks
-Atlas Iron sight plate
-Dawson Ice magwell with 1 used and 1 brand new insert
-3x different extra triggers, one red dirt, one infinity, one that I cant remember
-KKM .40 cal barrel with appropriate spring
-Atlas recoil spring tuning pack
-Wilson shock buffs
-6x Staccato basepads and springs to return the modded tubes to factory
-4x Grams spring/follower with TTI basepads for Staccato tubes
-Atlas thumb ledge
-Standard slide stop
-MPA shielded safety
-EGW mag release paddle
-Case
-Additional small parts not pictured
Gun and case ships to your FFL, all else will go to you direct. Insurance not included.
View attachment IMG_3782.jpegView attachment IMG_3783.jpeg
I’ve had this for about 2 years and I initially got it as a Gen 1 Titan chambered in .40 without an optic cut. I sent it out to DSC gunworks to get the following done:
-Recoat entire gun
-Bronze 9mm barrel
-Cut for Atlas optic plates
-Trigger job
-Cut for flashlight rail (if you have a good eye you’ll notice that the recoil lug slot isn’t as far back as it should be and you’d be right, the manufacturer info is on the bottom and he cut it as far back as possible without disrupting that. You can still run a X300-B if you remove the lug and just clamp it on the sides super tight. Lame, I know imagine my discontent when it was done without knowing that upfront)
Since then it’s got at least 4,000 rounds on it if I had to guess. None of the wear you see is from being negligent, I just used this gun a lot in dry fire and to be a USPSA gamer.
Includes:
-Gun
-Holosun 507Comp
-5x 23rd (as configured) 9mm mags 140mm
-3x 140mm MBX mags for .40cal
-3x various holsters, 2 have QLS forks
-Atlas Iron sight plate
-Dawson Ice magwell with 1 used and 1 brand new insert
-3x different extra triggers, one red dirt, one infinity, one that I cant remember
-KKM .40 cal barrel with appropriate spring
-Atlas recoil spring tuning pack
-Wilson shock buffs
-6x Staccato basepads and springs to return the modded tubes to factory
-4x Grams spring/follower with TTI basepads for Staccato tubes
-Atlas thumb ledge
-Standard slide stop
-MPA shielded safety
-EGW mag release paddle
-Case
-Additional small parts not pictured
Gun and case ships to your FFL, all else will go to you direct. Insurance not included.
View attachment IMG_3782.jpegView attachment IMG_3783.jpeg
