BDL metal for MCM M40A1 stock

[JelloStorm]

Remington has BDL bottom metal for $82.00 in their "closeout" section. Will this fit a McMillan M40A1 HTG stock that JW Precision has?

I believe that all I would need is the bottom metal,

Short action BDL box:
http://www.remingtoncountrystore.com/Par...amp;topcat=1038

And a BDL box spring and follower, which I'm not sure where I can find that at...

Correct?

 

[BobinNC]

Re: BDL metal for MCM M40A1 stock

Jello,

You can get all the parts you need, BDL Bottom metal, Mag Box, spring and follower from Numrich Arms.

Bob

 

[JelloStorm]

Re: BDL metal for MCM M40A1 stock

I've purchased HK parts from them before... total pain in the ass with their system. Do you know the BDL bottom metal part number for black matte?

And any other small parts I may need?

 

[Hateca]

Re: BDL metal for MCM M40A1 stock

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: JelloStorm</div><div class="ubbcode-body">Remington has BDL bottom metal for $82.00 in their "closeout" section. Will this fit a McMillan M40A1 HTG stock that JW Precision has?

I believe that all I would need is the bottom metal,

Short action BDL box:
http://www.remingtoncountrystore.com/Par...amp;topcat=1038

And a BDL box spring and follower, which I'm not sure where I can find that at...

Correct? </div></div>

Send me an email I may have a factory BDL option for you.

 

[Dick D]

Re: BDL metal for MCM M40A1 stock

Depends on what the M40A1 stock that JW has is inletted for.
It could be inletted for a factory BDL floorplate, an M40A1 bottom metal kit or one of the Badgers. What does his site say it is inletted for?

 

[JelloStorm]

Re: BDL metal for MCM M40A1 stock

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Dick Davis</div><div class="ubbcode-body"> Depends on what the M40A1 stock that JW has is inletted for.
It could be inletted for a factory BDL floorplate, an M40A1 bottom metal kit or one of the Badgers. What does his site say it is inletted for? </div></div>

I would say standard Remington BDL inletting. Here's what his site says:

Description: HTG Rem. 700 SA, right hand, Rem. 700, Rem. varmint b/c, bdl bottom inlet, 1" dec. pad, 1 bipod stud and 2 flush mount cups ( LH side ) machined aluminum pillars installed, molded in color, sniper fill, approx. 2.625 lbs

 

[mjh30]

Re: BDL metal for MCM M40A1 stock

Jellostorm, if you are going to be staying with the BDL floorplate for the forseeable future, may I suggest that you buy a quality aftermarket BDL floorplate rather than the factory one. PT&G make an excellent sturdy steel one, as does I believe Williams. Both of these are excellent products and significanrt improvement imho over the factory one.

 

[Kaisersose]

Re: BDL metal for MCM M40A1 stock

Jello,

If you have a stock inletted for the BDL setup from Remington.

Your easier options would be.

1. Find a used take off for around $55 in the for sale section.

2. Check out the Wyatt's detachable setup for around $225 that is supposed to drop in the BDL inlet
3. Also look at HS precision setup for around $225 that is designed to be drop in as well.

Just a couple more avenues.