Sidearms & Scatterguns Guns and coffee

[The D]

Ahhh, now I can deal with traffic

 

[Simonsza1]

New additions to edc life!

 

[pmclaine]

Tastes like a diner where you get served by a waitress that has a cigarette dangling from her lips….my new brew.

 

[Skunk]

 

[JR1200W3]

Tastes like a diner where you get served by a waitress that has a cigarette dangling from her lips….my new brew.

View attachment 8303879

Where's the gun? Do you think you're special and and deserve some kind of pass?

 

[pmclaine]

Where's the gun? Do you think you're special and and deserve some kind of pass?

It’s on the mug.

 

[JR1200W3]

It’s on the mug.

Well that's lame.

 

[pmclaine]

Well that's lame.

I don’t own guns…..they will shoot your eyes out.

 

[308pirate]

 

[MJF]

Tastes like a diner where you get served by a waitress that has a cigarette dangling from her lips….my new brew.

View attachment 8303879

What kind of picture is this? Needs bacon & a model 27.

 

[JR1200W3]

Been building this one for a while. Just got it to the point where it's ready for test fire so I took it out this morning and shot 50rds while tuning the ejector and extractor. Got it up and running. Still a lot of work to do. Thread barrel, DLC, stipple the grip, some blending and polishing, spring testing when I get the 220gr hard casts in. Tune a 126mm mag. But the fire controls, trigger, feed, extraction, and ejection are all good to go.

4.25" Kart 10mm on JEMs frame and slide. EGW parts, Harrison ignition kit.

 

[powdahound76]

Been building this one for a while. Just got it to the point where it's ready for test fire so I took it out this morning and shot 50rds while tuning the ejector and extractor. Got it up and running. Still a lot of work to do. Thread barrel, DLC, stipple the grip, some blending and polishing, spring testing when I get the 220gr hard casts in. Tune a 126mm mag. But the fire controls, trigger, feed, extraction, and ejection are all good to go.

4.25" Kart 10mm on JEMs frame and slide. EGW parts, Harrison ignition kit.

View attachment 8322377

Meh….

Just get a G20 bro!

Load n shoot.
No messin about.



Kidding (for those who dont know)

Looks really slick. Be anxious to see it when its threaded and all dialed.

 

[JR1200W3]

Me too. Ha ha! I've been slowly fitting it for 18 months. I got a bug up my ass to finish it in December. I was about to buy a Colt Delta Elite and decided I should finish this one before buying another 10mm. I think I'm going to buy another Kart Xact Fit barrel but in 40 S&W so I can do a flush cut crown and swap barrels. A Fly 45 will live on the 10mm. 220gr Hardcasts at 1050fps.

 

[Matt Moxness]

.......Needs coffee!
Found this like-new 1988-89 S&W M29-4, round butt, case colored 3" highly polished
blue unfluted cylinder to be the stable mate for my 629-Backpacker.
S&W used both a Pachmayr and Hogue grip on this model, 5:1 mfg with the Pachmayr "Presentation" grip style.
The same Pachymayr grip was designed for the K frames, but it apparently fit good-enough to mount it on their N frames.
It's handsome. I have the Hogue combat grip to mount.

View attachment 7890353View attachment 7890354View attachment 7890355View attachment 7890356View attachment 7890357View attachment 7890358

My hero Elmer Keith would be proud!

 

[strikeeagle1]

^^The Factory installed K-frame sized Pachmayr on this M29-4 N-frame and out-the-door they sold them.
Here it is with my preferred Hogue combat grips.

 

[strikeeagle1]

Double Expresso!
3" S&W Model 29 , .44 Mag., Blue Elmer-Horton v. Shiney Backpacker.

 

[strikeeagle1]

Just acquired a new-in-the box SA/DA shrouded hammer Smith & Wesson Model 49 no dash 1971-72 with mystical "floating J" serial number. The J-frame serial numbers prior, had the "J" leading the numbers. Apparently in 1971-72 S&W used up all their available sequenced j-frame serial numbers, so their solution was to "float" the "J" amongst the other 5 numerical positions until a better solution was secured. This one was resting in Cut Off Louisiana of all places. It's pretty handsome 2" 5-shot round butt.

Rounding out the old J-frame stable.