As title says. Let's see those defiance builds. I have a tenacity in 6cm im looking for a new stock for. Post them up.
- Thread starter FrozenMinnesotan
- Start date
Short Action Custom's build in 7 SAUM
Defiance Deviant GA Hunter
Manners EH1A
Razor AMG
Proof Research carbon fiber barrel
TriggerTech Diamond
TBAC Ultra 7 with Cole Tac cover
Defiance Deviant GA Hunter
Manners EH1A
Razor AMG
Proof Research carbon fiber barrel
TriggerTech Diamond
TBAC Ultra 7 with Cole Tac cover
Last edited:
Nice. Both manners stocks?
Manners prs1
Nice. I'd love one but don't have 1400 to drop quite yet
My .300NM build, built on a Defiance Deviant action with IonBond finish and the raceways polished:
Manners EH1A
Deviance Deviant, 338LM Bartlein 26" 1:10 5R Heavy Palma, McM A5, TBAC Can, Elite Iron Bipod, S&B 5-25x56 PMII, Spuhr 4601
Last edited:
I like it. It’s LRI’s wrought iron fluting
What stock is the lri built on?
Manners MCS T4a Elite matt clear carbon
Oh and this gem
All rifles built by Aaron Roberts of Robert's Precision Rifles Spring Texas
All rifles built by Aaron Roberts of Robert's Precision Rifles Spring Texas
Details of the build please?
Defiance Deviant Tactical SA stainless
Proof Research 1:10 26inch barrel .308 carbon fiber
Area 419 Sidewinder break
Trigger Tech Special DLC Flat shoe
MDT AAC hydrodipped by Applied Hydrographics
Atlas bi pod
MDT 12 round mags
Leupold Mark 5 5-25×56 there is. Kahles 6x24i AMR
i'm about to receive my firste deviant built and i'd like to keep it raw stainless but i'm a bit worry about the rust that could appears as it will be mostly use as a 2/3days hunting rifle;
as i saw a few stainless action,what does their owner think ?
as i saw a few stainless action,what does their owner think ?
Keep it lightly coated with oil or grease and you should be good
I'd personally nitride it.
Me too
thank you,
unfortunately when i ordered it from defiance machine i didn't know it could be nitride and i don't know any company that could do it( in France)..
the only coated option could be ,to have it duracoted(too thick i heard?)or cerakoted(better option i think?).
i like the look of the stainless so a matte clear cerakote could be fine but i don't know if it exists?
unfortunately when i ordered it from defiance machine i didn't know it could be nitride and i don't know any company that could do it( in France)..
the only coated option could be ,to have it duracoted(too thick i heard?)or cerakoted(better option i think?).
i like the look of the stainless so a matte clear cerakote could be fine but i don't know if it exists?
Leave it stainless then. I wouldn't cerakote it. Not unless someone can do the microslick version there.
Get it
Get it ION bonded/Diamond Like Coated . Call Defiance they will give you there POC that does all of theirs .the place is in North Carolina
He's in France...
Oh yeah missed that part . Now sure how that would work
Defiance Deviant Tactical LH in 7RM w/ 30MOA rail
McMillan ADJ-A6 w/ ghost flame pattern
Nightforce ATACR F1 7-35 MIL-XT in Seekins rings
Krieger 28” bbl 1:8.5/M24
Bix n' Andy TacSport Pro trigger @ 14oz
APA RTG bottom metal w/ CIP length mag well/mags
Atlas-CAL
SAS Arbiter (9”) w/ Rifles Only MAD
McMillan ADJ-A6 w/ ghost flame pattern
Nightforce ATACR F1 7-35 MIL-XT in Seekins rings
Krieger 28” bbl 1:8.5/M24
Bix n' Andy TacSport Pro trigger @ 14oz
APA RTG bottom metal w/ CIP length mag well/mags
Atlas-CAL
SAS Arbiter (9”) w/ Rifles Only MAD
Nice build. How much clearance do you have between the barrel and scope? What height Seekins rings?
Deviant Tactical x2 SA/LA
Both Proof Barrels
AXMC ×2 but stripping one of them
Both Proof Barrels
AXMC ×2 but stripping one of them
Not much. I'm using high rings (1") and I still had to shave off a little bit of the plastic off the bottom of the objective flip cover so that it cleared the barrel. I haven't measured, but I'm guessing I have ~.100"-.150" clearance now
Thanks for the info. Was curious since i have a Deviant Elite with MTU barrel coming that I will be topping with the same NF scope in ARC Medium (1.1”) rings. Will definitely be a tight squeeze, but planning on running without the front cap.
Mine is an M24. I think between no cap, and slightly higher rings, you should be gtg
My rifle is the first pic on this thread and that is a mtu barrel with arc medium rings. Perfect height for me, any lower You would have to trim the caps a little
Defiance deviant hunter 20 moa rail
Defiance bottom metal
Proof barrel chambered in 338 Lapua Ackley Improved
Christensen Arms titanium side port brake
Manners EH1 stock in scorched earth
Nightforce NXS 5.5-22x50
Nightforce 6 screw rings
FYI, in case this is what's holding you back on using a flip cap, it literally took me two seconds to shave the bit of plastic I needed to shave with a utility knife from the included NF caps, and I'm not even sure you're going to need that with another .100" of height on your rings.
It should, I did not have to trim the vortex caps
If all goes as planned, I'll get it put together this weekend and see where I land with it. No issues with trimming the flip cap if needed. I'll post up a pic once I have it together.
It won't help someone in France, but for those in the US, we suggest for DLC Club Custom Guns, and for nitride either H&M Metal Processing or MMI Tru-Tech.
Just about done. Deviant Elite, Bartlein 6.5 CM, and Nightforce ATACR 7-35 sitting in an MDT ACC. Ended up not needing to trim the front flip cap on the Nightforce with the MTU barrel. Waiting on the Area 419 bolt knob which I was hoping would show up today and then she'll be done. Just need to pickup a case of Berger 6.5 CM ammo and it's range time.
sweet looking builds. can't wait till next spring so I can build up a 300 WM.
