Finally went to the range today, and put the first shots through my new Christensen Arms Ridgeline .280 Ackley. I was shooting through my OCL Hydrogen-L 7.62 suppressor with the new OCL ZR0-DTA 5/8-24 direct thread mount. It’s a ridiculously lightweight setup for a 9” can. You really don’t even notice it on the end, as far as weight goes. It also sounds excellent!
So far still working on load development, so no results to post yet. I did notice that Christensen really cuts the chamber throats short on these. As a handloader, I’m not a fan. They are seated pretty deep into the case neck, even with Berger 168 VLDs. There’s plenty of room left in the magazine well, so I wish they would cut them a little bit longer (more normal). At almost 2 grains less than book load max, I’m already seeing pressure signs and ejector swipes.
I hope it shoots good. But that kind of pissed me off seeing as to how much this rifle costs. I might have to have a gunsmith cut (extend) the throat some, so I can seat the bullets farther out, and they won’t be taking up much needed case capacity to help relieve some chamber pressure.
On top sits an older Zeiss Conquest MC 3-12x56 30mm FFP scope. I’ve had this scope for nearly 15 years. It’s been on quite a few different rifles. It’s sitting in a set of Seekins Precision rings, on an EGW HD base.
![9CA49BA5-B8B1-46EA-A8B3-DA65D710D1C5.jpeg 9CA49BA5-B8B1-46EA-A8B3-DA65D710D1C5.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172527-2297ef5cf4e54f1ca8e8344cbdc11b33.jpg)
![E6BC3640-6A7C-4BBD-A441-CAD601E68B1D.jpeg E6BC3640-6A7C-4BBD-A441-CAD601E68B1D.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172529-47be2d2613a3b1b27c64f43ab87c3ebe.jpg)
![AF21255E-744B-4816-ACBD-584132A94FFA.jpeg AF21255E-744B-4816-ACBD-584132A94FFA.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172528-54ec29ee980054c1a6ff9555d9d79789.jpg)
![286CA6C2-B509-4CB9-88E1-3A2666B3CA0D.jpeg 286CA6C2-B509-4CB9-88E1-3A2666B3CA0D.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172530-2c42ca0957d9871108a183b48e73eee7.jpg)
![ABB97832-BF0D-475D-8872-7159C3D65D08.jpeg ABB97832-BF0D-475D-8872-7159C3D65D08.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172531-e986484ac15fa451ee7c629993fe503c.jpg)
So far still working on load development, so no results to post yet. I did notice that Christensen really cuts the chamber throats short on these. As a handloader, I’m not a fan. They are seated pretty deep into the case neck, even with Berger 168 VLDs. There’s plenty of room left in the magazine well, so I wish they would cut them a little bit longer (more normal). At almost 2 grains less than book load max, I’m already seeing pressure signs and ejector swipes.
![Neutral face :neutral_face: 😐](https://cdn.jsdelivr.net/joypixels/assets/7.0/png/unicode/64/1f610.png)
On top sits an older Zeiss Conquest MC 3-12x56 30mm FFP scope. I’ve had this scope for nearly 15 years. It’s been on quite a few different rifles. It’s sitting in a set of Seekins Precision rings, on an EGW HD base.
![9CA49BA5-B8B1-46EA-A8B3-DA65D710D1C5.jpeg 9CA49BA5-B8B1-46EA-A8B3-DA65D710D1C5.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172527-2297ef5cf4e54f1ca8e8344cbdc11b33.jpg)
![E6BC3640-6A7C-4BBD-A441-CAD601E68B1D.jpeg E6BC3640-6A7C-4BBD-A441-CAD601E68B1D.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172529-47be2d2613a3b1b27c64f43ab87c3ebe.jpg)
![AF21255E-744B-4816-ACBD-584132A94FFA.jpeg AF21255E-744B-4816-ACBD-584132A94FFA.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172528-54ec29ee980054c1a6ff9555d9d79789.jpg)
![286CA6C2-B509-4CB9-88E1-3A2666B3CA0D.jpeg 286CA6C2-B509-4CB9-88E1-3A2666B3CA0D.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172530-2c42ca0957d9871108a183b48e73eee7.jpg)
![ABB97832-BF0D-475D-8872-7159C3D65D08.jpeg ABB97832-BF0D-475D-8872-7159C3D65D08.jpeg](https://www.snipershide.com/shooting/data/attachments/1172/1172531-e986484ac15fa451ee7c629993fe503c.jpg)