Search results

I'm shooting a 6.5 cm with 42.8 of H4350.... MV is 2780..... barrel is a new 26" LRI "ELD X" and hopeful it speeds up a little....I am disappointed at the results I have had so far.

am interested in your load data for those two loads......I am using H4350

redding type S full length with .290 bushing..... which seems to work the best for me. I have .288, .289, .290, and .291... trial/error got me to the .290 bushing. Attached group was done with 2x fired Hornady brass. I have Lapua SRP brass as well and use the same .290 bushing. It has been my...

thanks gents! I've got the hornady app on my phone... and the 10th edition manual in print. I'll check that Sierra app out. If it is like Hornady's each caliber is like .99.

My sierra manual must be old....doesn't even list 6.5 cm 5th edition :)

It was the Hornady book.....

I'm going to try .080 and .100 jump next.... the attachment ....thank you for the advice.

thanks for the info..... i did not know how to do that. Since 43.4 of H4350 is a little above max shown in the loading manual I am wondering how the primer pockets are holding up in your hornady brass.

We've had some not so good weather, but I did manage to get out for a couple more tests with this LRI ELD-X barrel and the 130 Nosler RDF pills. I cleaned the barrel. Checked it with my bore scope and it looked good. Shot a 3 shot group with the old standby (good for .25 or under) load to foul...

On my RPR, I had an LRI (KP) barrel. It shot the Hornady match load extremely good. I had a load that duplicated the factory load. 41.5 H4350 with 140 ELD-M at 2.146 case base to bullet ogive. The 130 ELD-M with same powder charge also printed ragged hole groups at 2.151 base to bullet ogive...

thank you for your response.... never jumped them that far.... will give that a try. I started at -.020 and went out to -.040 and groups were going in the wrong direction....so the next go round I tried -.015 and another -.020 with similar results.

Looking for a good load using the 130 RDF nosler bullet. I've used 41.5 h4350 in Starline, and Lapua brass with seating depths -.020, -.030, -.040 off the lands, and nothing really consistent. So far, the best load looks like -.020. I can't load closer to the lands as the OAL of loaded rounds...

thank you....I am currently using an RCBS chargemaster to get close and then to check/verify with a gempro 250. The gempro seems to be quite sensitive to any room air current/ changes. Going by data from my V3 magneto I generally get 7-10 for SD, but it is fairly time consuming. I've loaded 100...

do you need a windows computer, or will a mac work (iOS )

Yes, I do enjoy shooting with the can and will do some further testing. That's what is happening. Start out out by threading on the can and the first POI is to the left of my intended POI, and the next four hit the intended POI. I bought this titanium can from Dakota Silencer specifically for...

This is my first suppressor, and I am wondering if this is common for all suppressors. When I make the first shot (cold bore or ambient temp) the bullet impacts 1"- 1-1/2" to the left of my aiming point. Then the next four rounds are touching and right where I was aiming. I've done this several...

according to my Magneto spd chromo, my 20" Tikka CTR suppressed mv 2580.and 2591.... sub 1/2"groups.....generally there will be someone at the range with a chromo that will help you get actual numbers for your rig.

Another good round out of my KSM was the Aguila Super Match. Not sure what the FPS is of that round. 5 shot group, but it was pretty consistent.

I've had my KSM for several months now, and am very pleased with performance and accuracy. (When I ordered the rifle I asked if they recommended a particular brand of ammo and the gal that I talked to suggested trying CCI STD Velocity) I ordered a couple of boxes of various brands of ammunition...

I checked their website. Looks like a fine place to shoot. Thank you for the info