Search results

Because I have morals and won’t pawn a piece of crap off on someone else? LOL I must have struck a nerve in the douche bags that think that’s acceptable behavior.

I’ll remember to never buy anything from you. That’s a shitty zero integrity move to pass on a rifle to someone that you believe to be a dud.

It’s going to a gunsmith for inspection and to get the issues in writing from a third party and then it will go before a judge. This post wasn’t asking for help figuring it out, I’ve figured out that it has some machining issues and likely a barrel stress issue. This thread is only to make...

I’m not going to shoot flat based bullets because there’s no factory 7PRC ammo with them. I bought this rifle to shoot factory ammo and it’s guaranteed to shoot 1MOA with factory ammo so that is my expectation. The issue is that the build quality is pure shit, the accuracy has gotten better...

The optic was parallax free, that was checked along with dozens of other things. If you read my original post you’ll even see that I confirmed that optic on another rifle on the first range trip and put the optic from the other rifle on the Bergara too with no change. On the Seekins I barely had...

Sleds usually make rifles shoot worse not better. I was shooting off of sandbags and shots were breaking clean. Also like I said in my original post I had absolutely no problem shooting my much lighter Seekins Element 7PRC on the same day off the same bags. Dry firing with both before shooting...

I’m very aware of what fire lapping does, I’m also very aware that putting lapping compound on a bullet and sending it down the barrel isn’t going to turn a 4MOA gun into a sub MOA gun. That’s not how it works. I’m also aware that most manufacturers will void your warranty for shooting bullets...

The reading comprehension here is low. I’ve owned 3 Bergaras now, not 4. I’m not sure where you guys are getting that but apparently some of you can’t read well.

Did you read the original post at all?

Casting marks are not pitting, pitting is a result of metal corrosion. I care far less about stuff like that than the machine surfaces that matter for function. If I want a pretty shotgun with a flawless finish to jack off on I’ll pick a high end over under that starts at 3x what an M4 costs...

That’s highly likely a cast part and from the casting and not pitting.

I was in sportsmans about a week ago looking at semi auto shotguns and picked up a SBE3 20ga since that was one of the top contenders and racked the bolt back and it locked up. I handed it to the hunting manager since I didn’t want to fuck with it because it wasn’t mine and they started trying...

The rifle has been shot with 4 different types of ammo and bullets including the Federal TA that Bergara guarantees it to shoot with. Factory ammo in 7PRC is still limited in flavors and I have zero interest in reloading for it. They guarantee it to shoot sub MOA with factory match ammo so it...

No, epoxy is never permanent. It’s no harder to remove than a thread with red loctite. Even if you could figure out how to successfully weld the aluminum base to the steel receiver that’s not even permanent. I use JB quick on scope bases because it only takes 300 degrees to remove vs 500...

Update on reply two after OP with some target pics. You mean the base that I’ve already removed once with a heat gun to send it in the first time because they wanted it with no mounts? 😂😂

The rifles suck but the CS is decent at least. My MPR had headspace .003” short of SAAMI minimum and wouldn’t chamber new brass or ammo without forcing it or sizing it back. I sized some back just to shoot it and it shot pretty well. Called CS and explained what was going on and they said they’d...

I’ve had several of these, still own one. They are not high end rifles but for the $1K or so you can actually buy them for it’s hard to go wrong. I’d still buy one today too. Doug Koenig certainly seems to do pretty well with one too. All of mine were gen 1’s and I think I paid $700-800 for...

I’ve yet to get a bad Remington. I’ve seen some that had the bore drilled so off center the crown was damn near on the side of the barrel, and I know friends who have gotten bad ones but even during freedom group QC it seems like the bad ones were very infrequent. Meanwhile I’m 0/3 on Bergarbage...

I wake up every morning, thank god for making me a tripod and not giving me your pathetic life. So I promise you I’m not mad. You’re welcome to fuck off and go be a retard elsewhere.

Holy hell you’re low IQ. So I take it that’s a no, you’re not going to put your money where your mouth is and take it off my hands? What film? You don’t seriously think they film the groups being shot for every rifle that’s sent back do you? The rifle shot a .9XX and a .6XX group (not any .5moa...