For one 243WSSM brass is the worst brass I've ever seen, period. 243 WSM??? probably 400 rounds barrel life.
- Thread starter Bluejazz
- Start date
For one 243WSSM brass is the worst brass I've ever seen, period. 243 WSM??? probably 400 rounds barrel life.
^ along with ridiculously long brass life if you are neck sizing or using custom dies. Been about 6 years now and that brass still holds a primer well! 2300 rounds on my Melonited barrel, .28" 5 shot group checking my zero last month.
my newest rig is a 6XC with a 20" barrel! I get 3050fps out of the 105 amax with 35.7gr of re15. this is a stout load but not hard on brass. the 6XC is very easy to form from 22-250 which is what I use or you can buy good norma brass for $75 per hundred. aside from the 6BR and 6PPC, this is the most accurate round I have had my hands on. the 6 creedmoor looks very promising too and it seems to form very well from the 22-250 by looking at the pic. I think the .243, SLR, crusader will give you problems chasing the lands and staying in magazine length. the 6x47 lapua looks nice but that damn brass is HIGH DOLLAR!
chuck
chuck
Bluejazz,
I honestly haven't seen this in the 6SLR, i loaded from high to low in .2grn and shot at 300yd ladder test and it was about a 3" group over a 4grn spread. The temp sensitivity is great for me living in ND with temp swings from -30 to 90f, not all in the same day of course. But i'd say a 50 degree swing during a day is easy.
xdeano
I honestly haven't seen this in the 6SLR, i loaded from high to low in .2grn and shot at 300yd ladder test and it was about a 3" group over a 4grn spread. The temp sensitivity is great for me living in ND with temp swings from -30 to 90f, not all in the same day of course. But i'd say a 50 degree swing during a day is easy.
xdeano
Here it is, maybe you missed this pic earlier? Unfired 22-250 case on left(one pass thru 6 Creed die), 6 Creed on right.
<a href="http://s1113.photobucket.com/user/JGorski80/media/IMG_0775.jpg.html" target="_blank"><img src="http://i1113.photobucket.com/albums/k513/JGorski80/IMG_0775.jpg" border="0" alt=" photo IMG_0775.jpg"/></a>
Here's the same case after firing, Hornady 6 Creed on right, again.
Fits in AW mags, AI with plate removed..etc. With dtacs I can put in the lands if I need to, or jump. There is room. Reamer is from George at GAP.
I did see that earlier, just wasn't aware that fireforming was required.Here's the same case after firing, Hornady 6 Creed on right, again.
How accurate are your fireforming rounds?
Do you have poi change from fireforming loads vs on once fired brass?
115 DTACS at 3010 fps, 26" Scneider 5P 7.5 twist, 42 grains H-4831SC, could go higher but the rifle shoots good here. AI mags. Add approx 100 fps if shooting 105's.
6mm SuperLR data page
http://www.6mmar.com/Super_LR.html
http://www.6mmar.com/Super_LR.html
Only shot the one, so Im not sure about accuracy. Id imagine once they're all formed they should be as accurate or almost as accurate as the Hornady stuff. Ive got 5 loaded up for forming, but Ill probably use them for break-in for my rebarrel job later this year. 30.5grs of RE15 with 105s is what I used to reform the 250 brass.
Quote Originally Posted by Bluejazz View Post
I did see that earlier, just wasn't aware that fireforming was required.
How accurate are your fireforming rounds?
Do you have poi change from fireforming loads vs on once fired brass?
Between my wife and I, we have formed almost 600 22-250's into 6mm Creeds.... We generally use a lighter bullet and faster powder and use the loads under 500 yards for positional practice. I have never tried the 105's as a FF load.
On a similar note: We shoot a 6.5 slr and the FF load uses 123's and faster powder and is less than 1/2 moa at 700...
I did see that earlier, just wasn't aware that fireforming was required.
How accurate are your fireforming rounds?
Do you have poi change from fireforming loads vs on once fired brass?
Between my wife and I, we have formed almost 600 22-250's into 6mm Creeds.... We generally use a lighter bullet and faster powder and use the loads under 500 yards for positional practice. I have never tried the 105's as a FF load.
On a similar note: We shoot a 6.5 slr and the FF load uses 123's and faster powder and is less than 1/2 moa at 700...
REVISED
243 WSM > 6 Crusader > 6 Competition Match > 243 AI > 6 Rem > 243 > 6 SLR > 6 Creedmore > 6 XC > 6x47 Lapua > 6 Dasher
I like the 6BR. 30.2grs of Varegt with the 105-107 and its a hammer. I have them feeding through a AICS mag with no trouble. ezaccuracy here on the hide did the conversion for me.
Im having a 6x47 built right now. I went this route just because I already have a couple 6.5x47's and like the brass. My smith already had the reamer and has done some others and they all shoot really well.
Thanks, that seems about right
What is the advantage of the 6 Creedmore versus the 6.5 Creedmore for bolt guns? I can re-barrel my LMT MWS in 6.5 Creedmore and am thinking about getting a bolt gun in the same caliber, but it looks like most of the options you are discussing in this thread are 6mm....Thanks
That's why the thread is titled 6 mm choice.
I don't think there is any advantage one way or the other that is significantly meaningful.
Other than the 6 mm will have less recoil. There are a lot of great 6 and 6.5 calipers to choose from. Just don't get bogged done to much in your choice. They are all great.
I didn't remember the title of the thread until I sent out my question, but you answered my question and I assume the 6.5 has a lot less recoil than a 308. Until recently I thought the 308 was the best caliber for long range (up to 1000 yards), but after reading a lot of threads I am now looking at a 6-6.5 mm load.
I was in the same position as you and went with the 6 Creedmoor.
Eddiemac,
I sold my 308's to get into a 260, now gathering imfo on 6 cals
I went back and looked at the Sticky, Tactical Shooters Equipment, Wht the Pros Use, and it looks like the best shooters are mostly using 6 mm, but there are some 260 Rem and 6.5 Creedmore thrown in (I need to decide on one of those two calibers to have the same ammo for my gas and bolt guns). Otherwise I would be looking at the same 6 mm calibers you are.
6BR. My buddy dominated the 1000yd matches last year with one.
