Recent content by ChadDoe8

The max case length for the .308 is 2.015. Trim to length is 2.005. And I agree with what is posted above; 2.015 should be safe but you will not know unless you actually measure your chamber. I also hate to trim brass but I will always trim when I approach .005 of max length. I figure one of...

If they aren't gouging then why did the CMMG .22lr conversion kit for an AR go from ~$80 to ~$200? Although, I haven't noticed much of a price increase on any other products.

I put my brass on a bamboo bar-b-que skewer (through the primer pocket) and heat the necks in a dark room just until they turn red. I then dump them immediately in water. This results in dead soft brass at the neck and shoulder but still good and strong at the head. My understanding is that...

Re: suggestions for a newb Turret, Where are you at in VT? Both the Rem 700 and Savage model 10 are great firearms. I have a savage model 10 that is anything but stock now. It started out as a stock .308 with a cheap 3-9 scope for about $350. I then upgraded and switched things out as i...

Re: A little help with Savage .300blk build Ryan, I looked at the accurate mag sight. They only talk about DBM for .308 sized cases and bigger. I do not know if the SA size will accept .223 sized mags, but I'd doubt it. I also checked out the CDI sight and found no mention of the .223 sized...

Re: A little help with Savage .300blk build Accurate-Mag makes a DBM that replaces the standard savage DBM but converts it to take AICS mags instead of the standard savage mags. I had a model 10 with a blind center feed mag. I bought a stock (HS precision) that was pre-inlet for the...

Re: Bipod Issue I've had the same issue on a Harris non-swivel. I've had it on a number of different stocks and it is always off level. It's not nearly as bad as the one you describe but it is annoying at times. Mine is a non-notched leg so I just adjust up until I level it out and then...

Re: need a good flintlock kit Having built one of each of those kits (chambers and track of the wolf), I'd highly recommend the chambers. But remember just because it's a pre-carved doesn't mean that you won't have a ton of work to do. You'll still need to inlet all the parts and do the...

Re: need a good flintlock kit Track of the wolf has some good stuff for sale. Are you planning on making your own or buying one already done up? I've made a couple (an Isaic Hanes, A Beck and I'm working a Schuler/buck's County now). If you are going to make your own visit Jim Chambers web...

Re: Help.....8mm Mauser questions And now that I look a little closer I don't see any steps on that barrel. It MIGHT be a re-barrel or a re-contured barrel. Check the caliber. Maybe I just can't see the steps in the picture due to the painting.. -chad

Re: Help.....8mm Mauser questions The only thing wrong with the 8x57mm is the anemic commercial loadings. If you are a reloader there are plenty of options and fun to be had with this granddaddy! What you have is a pretty common occurrence. A military Mauser 98 sporterized a bit. The...

Re: Best Savage Drop-In? I have a McGowen SS 22" .308 1/10" twist on my model 10. I ordered it from savage-barrel.com. I had zero problems with the order or the barrel. I haven't worked up reloads with it yet, but my results with over the counter fed 150gr softpoints has been way more than...

Re: Bump in the night set up? Whatever you do make sure it is secure from that 2 year old!! I have two young ones in the house, 8 and 6. They don't go poking around looking for stuff yet, but it's only a matter of time. I keep my 12 gauge in the closet with a cable lock through the action...

Re: Extended Bolt Knob Midway has a factory large bolt knob for $15. I put one in my Model 10 and it made a world of difference. http://www.midwayusa.com/Product/193602/...nob-steel-matte

Re: So frustrated, nothing went right... I agree with EMorr above. Don't worry about the chronograph data right now. The important thing to worry about is the pressure. Inconsistent chronograph data won't blow up your weapon, overpressure will. You're seeing pressure signs on your brass...