• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by Glock talk

  1. G

    KRG Whiskey 3 Chassis-Let's See Them

    picture sucks but i just got everything together rifle started as a bergara HMR PRO 6.5 creed i had a smith cut it to 18" and cerakote the barreled action. EA LUX 6.5 can Razor 4.5-27 Spuhr mount the W3 is amazing i have zero complaints, and cannot wait to get out to the range and get...
  2. G

    KRG Whiskey 3 Chassis-Let's See Them

    i have the W3 gen 7 folder on the way, im stoked. The chassis is going to replace the HMR stock/bottom metal on my HMR pro 6.5, the rifle is already very accurate so i doubt the W3 will make it shoot better but the ergos and looks should be 10/10.
  3. G

    16-18 inch shorty rifles

    HMR PRO 6.5, has a smith cut and rethread to 18” and cerakote the barreled action black. Suppressor is an EA lux, pst 2 3-15. Sounds awesome with the can
  4. G

    LMT .308 MWS

    Took my 16” mws out to some distance today. Setup isn’t the best with a pst 1-6, but I was shooting 168 hornady HPBT hand loads, G national match trigger, stock lmt everything else. Prior to this I had shot to 300 on steel so I knew my hold over for that distance. I then walked about 6 rounds in...
  5. G

    Anyone shoot an Energetic Arms Lux?

    I have a lux 6.5 and it’s dedicated to my Bergara hmr pro that I cut to 18”. Sounds amazing although my only comparison is a sandman S @24” factory configuration.
  6. G

    Defiance finish

    Can any of these finished be applied while a barrel is installed on the action
  7. G

    Defiance finish

    Traded for a build that has a deviant hunter action, amazing action and my first custom build. The stainless finish is not my thing though. I had read about cerakote being a no go On these actions because of tight tolerances. I don’t think exterior would be a problem and I really don’t care...
  8. G

    Bergara HMR Pro and $2500 question?

    Starting hand loads in mine were average of .3X lowest was a .2. This was with 140 Berger vld and 142 smk. I would suggest trying some different ammo.
  9. G

    DD Delta 5... 6.5 Creedmoor Range Report

    I did a break in procedure once on a savage 10t 6.5 creedmoor. Rifle shot .5 with 147 eld m reloads. I did not do any kind of break in on my Bergara 6.5 creedmoor. Rifle shoots in the .2-.3 with most loads I have tried.
  10. G

    Bergara for the win-Again

    Great rifles. I’m in early stages of load development and have a .2” group with 142 smk.
  11. G

    Hmr pro

    Very impressed so far, it will take me awhile to shoot this barrel out and hopefully they will offer a heavier contour by then.
  12. G

    Accuracy change after Barrel cut down

    Although not a cut down or a bolt gun. I swapped barrels in my lmt mws from a 13.5 with flash hider to a 16”. I had previously been shooting 168smk with 42.0 gr of IMR 4064. The 16” shot them better (.6 compared to .8)
  13. G

    Factory Ammo Recommendation for 6.5 Creedmoor 1/8 twist barrel

    Honestly I would roll your own. You will make up the cost if you are shooting a lot or just want to stock up. Outside of that I would try prime or gorilla ammo.
  14. G

    Hmr pro

    Finally got around to shooting my HMR PRO 6.5 today. Conditions were pretty terrible as the wind was pretty steady at 5mph and gust up to 10-15. Made it difficult to hold steady and my target was moving with the wind as well. enough excuses, I had loaded 5-3shot groups of 140 Berger vld and...
  15. G

    The battle of 308’s

    Only experience is with an MWS. mine started out as a 13.5 with perm attached flash hider. With a 4-16 vortex pst and 168smk I was able to achieve around .75” at 100. I decided that the weight of the gun is more suited to a dmr setup compared to a run a gun setup. I traded for a 16” barrel and...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts