Recent content by joe_skeeter

  1. J

    Is Lapua Brass a waste of money for an AR-15?

    Re: Is Lapua Brass a waste of money for an AR-15? Do you resize the body each time and full neck size? If so, don't you lose some of the advantages of good brass?
  2. J

    Is Lapua Brass a waste of money for an AR-15?

    I use Lapua brass in my .308 bolt gun and love it! But, is lapua brass to expensive for an AR-15. I catch my brass and seldom lose any so that is not a concern. Thanks
  3. J

    Paypal problems...dropped from online training

    Re: Paypal problems...dropped from online training I had to cancel my credit card I used for Online Trining/Paypal because of identity theft. I have setup a new credit card with Paypal but I keep getting a message that my subscription to Online Training has been canceled. What do I need to...
  4. J

    Problem depriming Lapua .308 Palma brass

    Re: Problem depriming Lapua .308 Palma brass I called Redding this morning and ordered the .057 decapping pins and they sent them out todays at NO CHARGE. Last week I needed a screw for my NightForce rings and they sent me two at NO CHARGE. What is going? Are companies focusing on...
  5. J

    Problem depriming Lapua .308 Palma brass

    Re: Problem depriming Lapua .308 Palma brass I am using redding dies. Thanks for the part number. This should fix the problem.
  6. J

    Problem depriming Lapua .308 Palma brass

    I am trying to reload my Lapua .308 Palma brass for the frist time and the decapping pin is being pulled out of the die on the up stroke. The pin is stuck in the case's small flash hole. I had to remove the pin manually with a punch. I hope there is an easier way to do this. Please help.
  7. J

    New AR-15 build

    I just got my rifle back from Gunsmiths Inc (Tim Ward) who upgarded my Les Baer AT-15 Police Special. I had Tim replace the barrel with a Krieger barrel with 1-7.7 twist. He cut it off to 20 inches, crowned it, and chamber it. Replaced the handguard with a LaRue Tactical 13.2 and a Magpul PRS...
  8. J

    Rifle Scopes AI scope unimount question

    Re: AI scope unimount question Thanks so much.
  9. J

    Rifle Scopes AI scope unimount question

    Does anyone have the torque specs for the AI unimount rings? I believe it is in newton unit of measurement.
  10. J

    GAP 3/8 MOA Guarantee fiction or reality?

    Re: GAP 3/8 MOA Guarantee fiction or reality? I did move the chrony out to about 10-12 feet. I now believe my chrony numbers.
  11. J

    GAP 3/8 MOA Guarantee fiction or reality?

    Re: GAP 3/8 MOA Guarantee fiction or reality? The crony fps were in question by several people and for good reason that they were wrong. I have firgured out what went wrong. The crony is a clam shell device and I had not fully opened the device to it's locked open position. The correct fps...
  12. J

    Accuracy International Pics

    Re: Accuracy International Pics AWSM 300 win mag
  13. J

    GAP 3/8 MOA Guarantee fiction or reality?

    Re: GAP 3/8 MOA Guarantee fiction or reality? The chrony was set about 4 feet from the muzzle. I was having a problem with the plastic sun-shades being blown off the chrony when I shot, but had that corrected by the time I shot the last string above. It could be the chrony.
  14. J

    GAP 3/8 MOA Guarantee fiction or reality?

    Re: GAP 3/8 MOA Guarantee fiction or reality? well the FPS numbers are what the chrony reported and calculated. I measured each load to exactly 41 grains. I was using brand new brass and maybe that had an effect. I don't know why I had a stddev of 63.54.
  15. J

    GAP 3/8 MOA Guarantee fiction or reality?

    I recently received my GAP Crusader in .308 and could not be any more pleased. I have been following GAP’s recommended break-in process. When I started shooting five shot strings between cleaning I also started my load development. On shots 36-40 I became a believer in the 3/8 moa guarantee...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts