• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by Kenny Blankenship

  1. K

    Maggie’s Funny & awesome pics, vids and memes thread (work safe, no nudity)

    Should about wear out your barrel with that!
  2. K

    Armed Agents in Round Rock, Tx. School District Arrest Concerned Parents in Their Own Homes

    I'm in commiefornia. There sure is a lot of BS going on here, but I'm not aware of anything like this!
  3. K

    Desert Tech SRS-A1 Aluminum Picatiny Rails

    Three for sure
  4. K

    Maggie’s Funny & awesome pics, vids and memes thread (work safe, no nudity)

    It's the "Monkeymobile".
  5. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Unless I am looking at a pic from the wrong thread, I see a monopod on the rifle. Also, the best rifle I ever had was a gen 1. Smooth as silk and consistent 1/4 MOA. I miss her. Sniff... The easiest way to see if it is a gen 1 or 2 is to open the bolt and look. Pin or feed ramp. Plus...
  6. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    How do you break a pin in the first place? Ihave an A1 now but I used to run a Gen 1. Just curious...
  7. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    I added a monopod to mine. It required having access to another rifle so I could measure exactly where to drill, then using a boring head to size the hole and make it ready to tap. I had to grind the tap flat to finish cutting to the bottom of the hole. It is a blind hole. As for the skins...
  8. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    I've seen some pretty inaccurate results come from using bore lasers. The SRS can be sighted pretty well by just looking through the barrel from behind the rifle (bolt removed). Or has this been resolved? I'd like to know the outcome.
  9. K

    DTA Help Needed

    About the "zero stop"; it has none because it has an EREK turret. It WAY better. No wasted elevation adjustment, no need for a 40 MOA base. Complete control built right into the scope.
  10. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    The inside of the receiver needs to be clean and free of anything that affects how it clamps to the barrel. Think burrs, paint from a sloppy camo job, etc.
  11. K

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    It sounds like you want the rifle to have Arca Swiss grooves molded into the skins, I think it best to use an adapter attached to the rifle. Made to fit, it would cradle the gun and attach to the provided hole. Most likely aluminum. Strong.
  12. K

    Effective Immediately, No Politics Period !

    Politics "Guess I missed it. Does this have any relation to '2nd Amendment' section not showing any content?" I was wondering this too. But this is not posted there... (nothing is) To me it's like the 'Hide has been castrated. I always dropped by the 2A section to hear about the latest...
  13. K

    mixing powders ?!?!

    I kind of like the avatar of High Binder mixing powders next to his post!
  14. K

    I think theres a lot of this problem in DC

    I disagree! The stuff that leaks out of DC is NOT a clear fluid!
  15. K

    Remington 788 build?

    Don't forget about the magazine. 22-250 is different from 223 there too. Perhaps a 250 Savage barrel? Same bolt face and magazine... Too bad you did not find a 788 like mine in 7mm-08. I have herd about the bolt handle breaking before - can anyone here relate a personal experience?
See more
Top Bottom
Back
Home
Forums
Merch
Alerts