• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by nuclabuyer

  1. N

    Gunsmithing X-caliber barrels???

    Ya, I can do that, I am going to have an order put in to PTG a little later for a 7 Saum reamer and then we will be ready to get it chambered and be ready to give it a shot. I am waiting for my new shop to show up so if it shows up between now and and the delievery of the shop, the chambering...
  2. N

    Gunsmithing X-caliber barrels???

    I just bought one in 7mm to try, we will see how it goes once I get it and the reamer togther. Plan is to make it a 7 Saum.
  3. N

    Rifle Scopes How are IOR Rings?

    Re: How are IOR Rings? I have a set on my 338 edge holding a Vortex Razor HD, work perfectly.
  4. N

    Sidearms & Scatterguns 1911 refinishing

    Re: 1911 refinishing I am not familiar with the product, I have been looking around and found this for a price prices
  5. N

    Gunsmithing Obermeyer

    Re: Obermeyer Perfect, that is what I was looking for. Thanks
  6. N

    Maggie’s Balls of TITANIUM

    Re: Balls of TITANIUM I have been up 110-130 on the Colorado back roads and it is stupid to do. You dont have time to do anything if there is a deer in the road or anything besides go splat. I had to sell my bike because it was getting to be to often of an occurance. So I figured I better...
  7. N

    Gunsmithing Obermeyer

    Re: Obermeyer I have seen a couple different people and smiths say that obermeyers are tighter then average. More then anything I am looking for whether a tight bore affects velocity and pressure. I read a post from Chad that says all the Obermeyer's he has chambered were tight, but that they...
  8. N

    Gunsmithing Obermeyer

    I have read that a lot of the Obermeyer barrels have a tighter bore then most any other barrels manufacturer. Does this have any effect on the velocity of the bullet and does it cause any higher pressure when doing load development? Looking at rebarreling a 338 edge because I am not getting the...
  9. N

    Maggie’s Look at what Wash. state did last night.........

    Re: Look at what Wash. state did last night......... Well, the awesome state that I live in, converted to a bunch of Liberal dumbass's, also passed a bill for recreational use. I used to like Colorado, but it is getting worse every time an election comes around.
  10. N

    Gunsmithing Sako M995

    Re: Sako M995 Rodale also makes a good base for these rifles also. I had Opti-locks for a while and ditched them for a Rodale base and heavy 30mm rings. Mine is in a McMillan A-5 now, but I am having a accuracy problem with my PacNor tube. Not sure what the problem is but I believe it is...
  11. N

    Gunsmithing 30-378 accuracy potential

    Re: 30-378 accuracy potential Generally I will go to the .2 increments but I have not ran into a caliber yet the will shoot a 1 inch group at a given load, say 116.5, and have it be that dramatically different at 116.2. If I was shooting a 3/4" group or a 1/2" group I would take the load...
  12. N

    Gunsmithing 30-378 accuracy potential

    Re: 30-378 accuracy potential it was all done at once by Pac-Nor.
  13. N

    Gunsmithing 30-378 accuracy potential

    Re: 30-378 accuracy potential I havent tried another scope on this gun but I did move this scope/ring combo on to my 6mm Dasher and it shoots like most 6mm BR and Dashers, 1/4 moa usually at both 100 and 300 yards. After that I went from Opti-lok ring/base combo to a Rodale 1pc base with no...
  14. N

    Gunsmithing 30-378 accuracy potential

    Re: 30-378 accuracy potential I have thought that and have taken some reloads that are a touch over an inch and they end up shooting even worse are 300. I am to the conclusion that something isnt right with some part of the gun. I can run 1 moa at 100 and 3 in at 300 with 116gr of 50BMG and a...
  15. N

    Gunsmithing 30-378 accuracy potential

    Re: 30-378 accuracy potential There is minimal freebore according to pacnor. I had to send the barrel back to them to have them add a touch more freebore because I was getting high pressure with everything I reloaded including factory ammo. I had to open the action shooting factory ammo with...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts