Recent content by patriotnation

  1. P

    My bullet lube test results

    If you only brushed inside the necks on only one of your groups and you annealed them all, that would make a difference I think. If you anneal, then you should brush
  2. P

    Amp Mate

    I just ran 300. Dasher through mine and had maybe 10 failures, mostly brass falling out or whatever. Maybe I need to try a Lee shell holder. Sometimes it goes really smooth, other times not so much. So I have to babysit it but get other things done while it runs so all in all it saves some time.
  3. P

    D.O.P.E change with electronic target?

    Maybe the target was not stapled in the middle I don’t see how sensors can affect POI Good luck
  4. P

    Little Crow Gunworks: Avg POI Is More Important Than Group Size. Thoughts?

    That didn’t take long
  5. P

    Little Crow Gunworks: Avg POI Is More Important Than Group Size. Thoughts?

    Yep, it convinced me to download it and learn to use it.
  6. P

    Little Crow Gunworks: Avg POI Is More Important Than Group Size. Thoughts?

    I have watched this whole series and it has confirmed much of what I know and do, while also learning a lot. It makes sense to me that before group size, you must consider POI first. After all, what good is that one tiny group if it is much farther away from your point of aim?
  7. P

    Easiest way to chamfer inside of necks

    Like this? https://kmshooting.com/product/small-17-6mm-reamer/ Very consistent
  8. P

    MDT ACC Premier Gen 2 experience? review?

    I have my Vudoo 360 with a 22” straight Bartlien barreled action in one and it is a perfect fit for me. Comes in just above 15 pounds. Matches my centerfire rifle in an ACC as well. The 15” fore end Is just about right and leaves plenty of support for balance. I will say the adjustable butt...
  9. P

    SD's

    I shot 34 rounds today and got an SD of 4.0 6 dasher in Alpha brass I am more concerned with ES
  10. P

    Need to build a linear moving target

    Yes I have seen comments on garage door opener but you need to use Commercial duty ones to run it all day in a match. If they were reliable, it is a good start. A mover at a range in NY was a Ferris wheel type with 4 rimfire targets, homemade also. It had adjustable speed. Not linear but a mover.
  11. P

    Need to build a linear moving target

    I was looking at these for rimfire mover for matches where we have berms. I was thinking make up a track of some kind for behind the 100 yard berm, and have a sled of some kind on maybe roller skate wheels or something attached to this so the cable is protected, the sled is also behind the berm...
  12. P

    Maggie’s The Wood Shop

    I finally built this bedroom set my wife has patiently waiting 20 years for a few years ago. I just noticed this thread, there is some really talented folks on here. And here is a YouTube I put together of my build.
  13. P

    Looking for some help with my prone shooting in MA

    Where in Mass? I’m on the south shore
  14. P

    Hornady Bullet Comparator and OAL Tool Measures over .050" too short

    When I use that tool with a modified case, I can never get the calipers to line up perfectly straight in line because it is on an angle. Maybe your measurement if off because of that I don’t know but that could explain the discrepancy. Or like others have said, forcing into landscaping has gone...
  15. P

    Maggie’s Things Trump Should On His First Day............

    I’d be more concerned with what he does now, way before his first day as far as SS protection. He needs some overwatch to oversee and prevent incompetence or bias.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts