• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by peewee

  1. P

    Rifle Scopes Mike @ cs tactical

    Yes, good guy to do business with!
  2. P

    Dead on case trimmer - FANTASTIC PRODUCT!!!

    I spoke with Dustin the other day about this very issue. He said that he would have to pay a die/tool maker to grind this profile on each cutter, and that each 3 way cutter would have to be case specific. Cost would be around $100 just for each cutter that would then fit inside his housing. So...
  3. P

    Dead on case trimmer - FANTASTIC PRODUCT!!!

    Here u go. Dustin Youngdell. [email protected]
  4. P

    Hunting & Fishing 6 XC for coyotes and want to save fur

    I use the 58g Vmax in my 243wssm loaded down to 3300 fps. 600 yds would be no problem. Out of the 40 or so coyotes I shot last season I only had 2 blowouts. 1 was a pup, and the other was a very thin mangy female and both were broadside shots. I also use the 75g Vmax which would take you out to...
  5. P

    Bench-Source Annealer - how to convert yours to run on one 10lb propane tank.

    Your explanation makes a lot of sense. Thank you! I spoke with David earlier today (owner of Bench source) about this question and he said he thought the BBQ regulator and hoses would work but he was unsure how much psi was needed in a regulator. Now after your explanation I realize that's more...
  6. P

    Bench-Source Annealer - how to convert yours to run on one 10lb propane tank.

    Help me understand why a $30 two hose regulated setup like the ones mentioned above won't work? If the torch heads are left wide open, then there should be no restriction and u should be getting a regulated 10 psi thru the torches. This is typically enough to run the burners on a BBQ grill so...
  7. P

    Dead on case trimmer - FANTASTIC PRODUCT!!!

    Glad I found this thread. I had just called "the worlds finest trimmer" guy to ask a few questions about his product. I must say he was less than enthusiastic and seemed a bit put off by my few questions. Very short. That conversation made me do some more shopping around. Can't afford a...
  8. P

    Reloading press advise

    Forster Co-Ax, best single stage press in my book. Single stage for precision rifle reloading. Dillion for pistol or bulk 223. Just my thoughts
  9. P

    Rifle Scopes Switchview Lever?

    I have the IOR 3.5-18x50. I have tried several of the switch view levers including the new Eagle Eye plastic adjustable one. None of these are working. The stock nub on the mag ring is too high to fit a switchview but not high enough to easily move the magnification. Anyone found something...
  10. P

    Rifle Scopes Aadmount flip up scope covers

    U probably should have asked that question before the purchase:) but yes it's a great product. You should be happy!
  11. P

    Decisions Decisions, GA Precision or Tactical Rifles inc

    OMG!!! I have not laughed so hard in many years. My eyes were tearing up. You rock!
  12. P

    .243 Win. for the AR platform.

    Just a note. I have several 243wssm in the AR platform. I shoot a 12 twist in all of them. I shoot the 55 to 75g pills at anywhere from 3600 to 3900 fps and I just finally shot out my first barrel with a round count of 3300. In fact the rifling was still fine it was the chamber that was...
  13. P

    Power setting for 100 yds

    That's because the glass in that scope sucks. Why do u think ppl pay $4k plus for good glass.
  14. P

    Lubes for extreme conditions

    Run it Dry in extremely cold or dusty conditions.
  15. P

    Ambidextrous safety

    I have a DPMS lower that only has the safety on the right side. Can I turn it into a Ambi setup by just adding one of these kits? Sorry new to AR's.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts