Recent content by pkt1199

  1. pkt1199

    Need Tech Support? Send a Private Message to @alexj-12

    @alexj-12 - sent a PM last Thursday regarding a friends locked account. Please advise.
  2. pkt1199

    Firearms GA Precision - GAP 10 6.5CM (Gen 1) - Price Reduced!

    Sold
  3. pkt1199

    Firearms GA Precision - GAP 10 6.5CM (Gen 1) - Price Reduced!

    Price reduced! ttt
  4. pkt1199

    Firearms GA Precision - GAP 10 6.5CM (Gen 1) - Price Reduced!

    For Sale - GAP 10 Gen 1 in 6.5 Creedmoor. I purchased this new back in 2013 (10 month lead noted on the build sheet!) and it has primarily been a safe queen since. I don't have an exact round count but would estimate around 400 on it. It cycles, shoots, and groups great like you'd expect from...
  5. pkt1199

    Accessories 6 GT Ammo, 6 BR Ammo, 6GT Alpha Non OCD Brass, Whidden 6BR Bushing Dies

    I'll take the 6GT barrel.
  6. pkt1199

    Range Report 6GT Project/Range Report

    Speed doesn't seem bad, you may be able to squeeze a little more out but probably not far from roughing up your brass. At least for me that was the case. I'm running 108s at around 2925-2930 (up maybe 15fps from where it was with previous lot of varget, 34.1gr), had a great node a few tenths...
  7. pkt1199

    Vudoo V-22 fit in foundation stock

    Ahh, I was thinking the Centurion stock rather than Revelation. I think they were going for a lighter build with that model and it looks like there is less stock in general (less material on the sides of the barrel, lower cut). So yours is likely showing more gap than the pics I posted above...
  8. pkt1199

    Rifle Scopes Zero Compromise Optics showcase!

    Sorry no outdoor glamour shots but for those curious on how the ZCO rings look... Similar to what @Dthomas3523 said above, I typically run ARC rings but figured I'd give these a shot. They feel good and to my untrained eye look to be machined very well. Couple things I noticed that are...
  9. pkt1199

    Vudoo V-22 fit in foundation stock

    Left is Vudoo 20" MTU Right is 26" M24 (not rimfire) These are not Revelations but I imagine the barrel channel is the same across the board. While there is the small gap...I can live with it given how great the rest of it looks :love:
  10. pkt1199

    Homemade Induction Annealer

    Nope. 308 is the biggest I've run but zero issues.
  11. pkt1199

    Homemade Induction Annealer

    There certainly is not much force. The trap door/paddle on mine can basically swing freely, like with gravity if you move it around(without solenoid attached). I used little bitty screws to assemble and connect things with a washer or two for contact points.
  12. pkt1199

    Homemade Induction Annealer

    @tyfoon Was printed with the top down and yep it had to have supports. It was actually on my brother's printer as mine isn't setup for PETG, sorry I don't know other details off hand but can ask if needed. I've only done 6 GT and 308 cases so far which fit the larger shell holder perfect.
  13. pkt1199

    Rifle Scopes Official Zero Compromise Optic News & Updates

    Mine is being shipped to me right now, which was about a six week wait. Let's say they announce tomorrow or even at SHOT months from now, that a higher mag is coming, how long do you think that wait will be? I'd wager you're looking at next summer at the soonest if not MUCH further out. If...
  14. pkt1199

    Rifle Scopes NF Scopes or Leupold?

    Provided you said best scope and didn't mention a budget... Start Googling Tangent Theta and Zero Compromise Optics.
  15. pkt1199

    Homemade Induction Annealer

    Those are cabinet drawer handles that have had one side cut off. And you're correct, can slide the platform on them for varying brass sizes.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts