• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by prosise

  1. P

    Off the lands question

    Re: Off the lands question <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: MinorDamage</div><div class="ubbcode-body">Taking a COAL measurement is asking for trouble. Bullets vary from ogive to tip and you may end up loading them closer or farther away than you...
  2. P

    What a good powder throw?

    Re: What a good powder throw? Can it be done, Hell yea. Easily. I would recomend batch loading for precision. You know, clean, size, prime, then throw powder all together. Get your powder thrower off a busy bench. Put it alone so no vibration will change the throw from case to case...
  3. P

    Lapua Brass- split necks

    Re: Lapua Brass- split necks Personally you have a couple options. I would use Redding type S bushing dies & remove the Expander. The set comes with the non expander button. I was told by Speedy Gonzales that you should not size twice. Sizing dies size in on the down & then you size out...
  4. P

    On Neck Turning?

    Re: On Neck Turning? Sure wanting to bite my tounge on this one, Sorry brother but I am not quite following you on the explanation. Couple of additional things might help. Is this a standard chamber or tight neck chamber? New or used brass? If new, did you OAL trim Then expand to uniform...
  5. P

    Light primer strikes or dud primers?

    Re: Light primer strikes or dud primers? Pull one of the bullets out, just to be safe. Start putting layers of masking tape on the back of the case, easch layer will add about .003-.004 to the OAL of the case. See how many you can put on before the bolt will not close. It would be nice...
  6. P

    Anyone ever modify shellholder or Die ?

    Re: Anyone ever modify shellholder or Die ? I have had to take some off the base of the sizing die on my 6br, and 6.5x284 redding type s dies. My gunsmith told me it is better that cramming the shellholder and dies. I took .o25 off the dies with a lathe. I had the same issue, needed a...
  7. P

    Accident at the Range today,+ some basic Q's

    Re: Accident at the Range today,+ some basic Q's <span style="color: #FF0000">1) I saw what he meant by "flat" primer, but don't understand what the cause could be, if it's not a hot load.</span> When you prime on a large press it sometimes flattens the primers, no biggie. <span...
  8. P

    Newbie Reloading- Headspace sanity check

    Re: Newbie Reloading- Headspace sanity check Here is a little trick I was shown when i first started shooting benchrest. Now this works on Remington actions: Or the like. Get a firing pin removal tool & take your bolt apart, takes like 5 seconds, you dont want the firing pin spring...
  9. P

    micrometer seating die what do you like ?

    Re: micrometer seating die what do you like ? I too like the Wilson seater, I like the feel, I can tell if one is hard to seat. That round becomes a fouler... prosise
  10. P

    Short Range Match Load: Am I out Gunned?

    Re: Short Range Match Load: Am I out Gunned? Who cares if your out gunned. If you go out and shoot your 308 , and you truly shoot the best you can you will have fun. I have shot benchrest for 4 years and I shoot the 6br with a benchrest setup, but on a remington action. I have beat many a...
  11. P

    Berger 95 VLD ?

    Re: Berger 95 VLD ? I use the Berger 95 vld, 105vld, and the Sierra 107's in my 6br. It shoots real nice but the VLD's wont expand like a Ballistic tip, or soft nose bullet. If you are shooting long range accuracy they are awesome. I have shot them in 1-8, and 1-10 twist barrels (20"...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts