Recent content by slapshot.308
-
S
Resizing for AR
Re: Resizing for AR Not recommended. Spend the money and buy an RCBS Precision Micrometer. Bump the shoulder at least .003" (most recommend .005") and seat the pimers at least .003" below flush. You should be reloading with a good FL die and might have to use a small base die depending on...- slapshot.308
- Post #2
- Forum: Reloading Depot
-
S
an observation on ANNEALING
Re: an observation on ANNEALING On .308, I hold them at the tip of the inner jet for ~8 seconds. The question concerning how many loadings is a crap shoot. I cannot give an estimate, only advice to keep close watch over them and cull them when one cracks. If you made it to 5 loadings, then...- slapshot.308
- Post #4
- Forum: Reloading Depot
-
S
Whale Wars looses a boat
Re: Whale Wars looses a boat Can't support the Japanese concerning whaling, I see no other point than profit. But have no sorrow for the Sea Shepard's either. Come on, you harass a vessel and antagonize the crew in international waters and then "park" your carbon fiber speed boat in front of...- slapshot.308
- Post #39
- Forum: The Bear Pit
-
S
an observation on ANNEALING
Re: an observation on ANNEALING If you over anneal (too much heat) you burn the zinc out of it. This in turn makes the brass brittle and will result in cracked necks. For a duration of 15 seconds you must be using a low temperature. At what temperature was the brass annealed at? If you over...- slapshot.308
- Post #2
- Forum: Reloading Depot
-
S
rem.700 .308 recoil
Re: rem.700 .308 recoil Well, when the weather gets warmer let us try to get together and shoot at APG (I assume that's where you shoot). No need to fight the cold while focusing on form.- slapshot.308
- Post #7
- Forum: Bolt Action Rifles
-
S
rem.700 .308 recoil
Re: rem.700 .308 recoil Then go naked, sans brake. The best way to control the recoil of the rifle and help with muzzle rise is proper form. Probably not what you were wanting to hear, but no piece of gear will correct improper form. Assuming that your form is down pat then the decision is...- slapshot.308
- Post #5
- Forum: Bolt Action Rifles
-
S
rem.700 .308 recoil
Re: rem.700 .308 recoil A suppressor would solve both felt recoil and blast... but costs more than a simple brake. Adding weight ill help with felt recoil, but then the rifle starts to become heavy and awkward in positional shooting.- slapshot.308
- Post #2
- Forum: Bolt Action Rifles
-
S
Powder for 5.56
Re: Powder for 5.56 Another vote for Ramshot TAC. Works very well in my AR.- slapshot.308
- Post #6
- Forum: Reloading Depot
-
S
problems with 223/5.56 reloads
Re: problems with 223/5.56 reloads Check shoulder bump and inspect for shoulder/body junction swell (set back in an AR should be .003-.005 inches). <span style="font-weight: bold">Remove lubricants from sized cases</span>. Trim cases to minimum. Inspect the cartridge OAL off the bullet ogive...- slapshot.308
- Post #18
- Forum: Reloading Depot
-
S
Suppressors 1911 pistol question
Re: 1911 pistol question A good checkering job can be done for $150-250. If it's grip, buy some skateboard tape and press on.- slapshot.308
- Post #5
- Forum: The Armory
-
S
Suppressors Why 9mm?
Re: Why 9mm? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: doorkicker</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: joe90</div><div class="ubbcode-body">So I was wondering why the military has been...- slapshot.308
- Post #102
- Forum: The Armory
-
S
Suppressors Why 9mm?
Re: Why 9mm? Shut up, SHUT UP , <span style="font-weight: bold"> SHUT UP ALREADY!!! </span>- slapshot.308
- Post #99
- Forum: The Armory
-
S
Suppressors bet 1911 ccw...
Re: bet 1911 ccw... <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Downzero</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: marduk185</div><div class="ubbcode-body">wouldnt a m-9 be better anyway...- slapshot.308
- Post #25
- Forum: The Armory
-
S
Suppressors bet 1911 ccw...
Re: bet 1911 ccw... <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Downzero</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Kevin Beggs</div><div class="ubbcode-body"> I'd like to know what you're...- slapshot.308
- Post #20
- Forum: The Armory
-
S
Suppressors bet 1911 ccw...
Re: bet 1911 ccw... <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: sickeness</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Kevin Beggs</div><div class="ubbcode-body"> To give you an example, Rock...- slapshot.308
- Post #15
- Forum: The Armory
